manualshive.com logo in svg

Laversab 6300, User Manual

Share
Download
Laversab 6300 User Manual Download Page 43

36

 

 
 

typical setting for this limit is 1.0. 
  

4.  Max. Feet  :

 

This  limit  is  usually  set  to  the  maximum  altitude  that  the  aircraft 

instruments  can  tolerate.    The  maximum  value  is  80,000    and  the  minimum  is  0.    A  typical 
setting for this limit is 50,000. 
 

5.  Min. Feet   :

 

This  limit  is  usually  set  to  the  minimum  altitude  that  the  aircraft 

instruments can tolerate.  It is usually a negative number.  The maximum value for this limit is 
80,000 and the minimum is –16,000.  A typical setting for this limit is –2000. 
 

6.  Max. Ft./min  :

 

This  limit  is  usually  set  to  the  maximum  rate  of  climb  that  the  aircraft 

instruments  can  tolerate.    It  is  usually  limited  to  the  maximum  indication  on  the  Vertical 
Speed  Indicator  (VSI)  on  the  aircraft.    The  maximum  value  for  this  limit  is  25,000  and  the 
minimum is 100.  A typical setting for this limit is 6000. 
 
To modify a limit, select the limit by entering its serial number (1 to 6).  The entry field will be 
blanked  and  a  new  value  can  be  entered  into  it,  followed  by  the  “ENTER”  key.    The  value 
becomes  effective  as  soon  as  it  is  entered.      In  the  screen  shown  below,  “1” was selected  to 
modify the max. knots limit. 
 
Note:  To set a negative value, enter the positive value and then press the “+/-“ key. 
 
 

                                          SET LIMITS 
1.  max. knots =  

              

              4.  max. feet   =     50000  

2.  min. knots  =   -200.0                 5.  min. feet     =    -2000 
3.  max. mach =   1.000                 6.  max. ft/min.=     6000 

 
The  CLR  key  is  used  to  clear  the  value  entered.    The  CANCEL  key  is  used  to  exit  the  SET 
LIMITS screen. 
 

 
 
3.5.3  FUNCTION 3:  SET KNOTS RATE

 

 
Pressing “3” on the Function Select screen brings you into the “Set Knots Rate” screen.  This 
screen is shown below. 
 

  
CURRENT  RATE   =   250.0     knots /min. 
        NEW  RATE   =  

             

   knots /min. 

 min :  50 ,     max :  500 

Summary of Contents for 6300









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands