Frequently Asked Questions
7
§
Before starting the engine, put the gear lever in NEUTRAL (for manual
transmission) or PARK (for automatic transmission) to avoid injury.
§
Do not connect or disconnect any test equipment while the ignition is on or
the engine is running.
Safety Instructions
§
Always perform automotive testing in a safe environment.
Disclaimer of Warranties and Limitation of Liabilities
All information, specifications and illustrations in this publication are based
on the latest information available at the time of printing. We reserve the
right to make changes at any time without prior notice.
§
Wear an ANSI-approved eye shield when testing or repairing vehicles.
§
The vehicle shall be tested in a well-ventilated work area, as engines
produce various poisonous compounds (hydrocarbon, carbon monoxide,
nitrogen oxides, etc.)
§
Do not drive the vehicle and operate the test equipment at the same time.
Any distraction may cause an accident.
§
Put blocks in front of the drive wheels and never leave the vehicle
unattended while testing.
Before using this test equipment, please read the following safety
information carefully.
§
Keep clothing, hair, hands, tools, test equipment, etc. away from all moving
or hot engine parts.
§
Keep a fire extinguisher suitable for chemical, gasoline and electrical fires
nearby.
§
To avoid damaging the test equipment or generating false data, please make
sure the vehicle battery is fully charged and the connection to the vehicle
DLC (Data Link Connector) is clear and secure.
§
Automotive batteries contain sulfuric acid that is harmful to skin. In
operation, direct contact with the automotive batteries should be avoided.
Keep the ignition sources away from the battery at all times.
A:
Usually, it's caused by poor connection or fault circuit grounding.
A:
1. Switch the tool on and ensure a stable internet connection.
2. Whether the "Automatic detection on Connect" switch is OFF. If
yes, slide it to ON.
Q:
How to upgrade the system software?
Q:
There is no response when communicating with on-board
computer.
Q:
Why are there so many fault codes?
Q:
What to do if the system fails to start auto VIN detection?
3. Follow the on-screen instructions step by step to finish the
process. It may take several minutes depending on the internet
speed, please be patient. After upgrade is successfully
finished, the tool will automatically restart and enters the Job
menu.
2. Tap "Setting" on the Job Menu, select "About" -> "Version", and
tap "Detect the System Version" to enter the system upgrading
page.
Here we list some frequently asked questions and answers related to
this tool.
1. Whether the tool is properly connected to the vehicle's DLC.
A:
Please check the following possible reasons:
Q:
What if the tool cannot be switched on even after a period of
recharging?
A:
Please recharge it for at least 3 hours until the power LED lights
up, then it can be switched on.
A:
Please confirm the proper voltage of power supply and check if the
throttle has been closed, the transmission is in the neutral
position, and the water is in proper temperature.
Summary of Contents for TOUCH PRO ELITE
