background image

Launch                                                                                          TLT235

TLT240 Economical Two-post User’s Manual                 

12

00

mm

(4

7.

2i

n)

800mm(3

1.5in)

3563mm(140.3in)

2415mm(95.1in)

 

Fig.3b 

2.2 Main structure principles: 

z

 

Lifting mechanism: Each column is installed 
with a hydraulic cylinder, when hydraulic oil is 
pressed from power pack into the lower 
chamber of main cylinder, piston rod moves 
upwards to drive the upward movement of 
carriage through leaf chain. 

z

 

Load supporting mechanism

When vehicle 

drives into the working area, adjust the angle 
and telescopic length of arms to make lifting 
pads at an effective load supporting position 
that contact with vehicle, then adjust the lower 
screw ’s height of lifting pad to make it 
applicable for vehicles with different chassis.   

z

 

Balance mechanism

In order to keep machine 

balanced during lifting and lowering, two 
carriages are interconnected and forced to 
move synchronously by two wire ropes. If the 
right and left carriages and arms are not at the 
same level, adjust the end nut of wire rope and 
pull wire ropes tight to make arms leveled. 

z

 

Manual safety locking system: the safety 

locking plates are installed on the two 

carriages and the toothed bar plate is welded 

on the internal wall of the column. During the 

lifting of the carriage, the safety locking plate 

goes up against on the toothed bar plate by 

the tension of spring. When the carriage stops, 
the safety locking plate opens and then is 

engaged in the toothed bar slot to ensure the 

carriage will not go down; when the lowering 

operation is required, just raise the carriage 
upward a little to loosen the safety locking 

plate from the toothed bar slot, and then 

manually pull the steel wire rope so as to jack 

up the safety locking plate by sliding plate, so 
the safety locking is released so that the 

carriage can be lowered down. Because the 

manual safety locking systems are installed on 

the two carriages, double safety protection can 
be provided; therefore, to disengage the safety 

locking, the steel rope on the two carriages 

shall be respectively pulled. To prevent the 

vehicle slip, the swing arm is installed with 

positioning mechanism, making the swing arm 
capable of automatic locking during operation. 

z

 

Safety lock scope: Safety lock mechanism is 
effective when the front end of carriage is 
between 450mm and 1900mm high above the 
ground. 

 

 

 

Summary of Contents for TLT235



















































Reviews: