Lattice Semiconductor MIPI User Manual Download Page 28 | Manualshive

Page: 28 / 31

Lattice Semiconductor MIPI User Manual Download Page 28

MIPI DSI to OpenLDI/FPD-Link/LVDS Interface Bridge Soft IP

User Guide

© 2016 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

. All other brand or product names are

trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

28

FPGA-IPUG-02003-1.2

Appendix A. Resource Utilization

Table A.1

lists resource utilization for Lattice CrossLink FPGAs using the MIPI DSI to OpenLDI/FPD-Link/LVDS Interface

Bridge IP. The performance and utilization data target an LIF-MD6000-6MG81I device with –6 speed grade using Lattice
Diamond 3.8 and Lattice Synthesis Engine. Performance may vary when using a different software version or targeting
a different device density or speed grade within the CrossLink family. Programmable I/Os do not count miscellaneous
status signals. The values of f

MAX

shown are based on continuous byte clock. The Target f

MAX

column shows target byte

clock frequency for each configuration. See the

Reset and Clocking

section on page 13 for more details on supported

clock frequencies.

Table A.1. Resource Utilization

IP User-Configurable
Parameters

Slices

LUTs

Registers

sysMEM

EBRs

Programmable

IOs

Actual f

MAX

(MHz)

Target f

MAX

(MHz)

Single Rx to Single Tx,
RX_GEAR=8, TX_GEAR=7,
RGB888,
Non-continuous D-PHY clock

733

882

800

3

12

119.175

112.5

Single Rx to Single Tx,
RX_GEAR=16, TX_GEAR=14,
RGB888,
Non-continuous D-PHY clock

1496

1865

1495

6

12

92.132

64.285

Single Rx to Dual Tx,
RX_GEAR=8, TX_GEAR=7,
RGB888,
Non-continuous D-PHY clock

750

910

828

3

17

122.579

112.5

Single Rx to Dual Tx,
RX_GEAR=16, TX_GEAR=14,
RGB888,
Non-continuous D-PHY clock

1525

1921

1548

6

17

107.945

93.75

Dual Rx to Dual Tx,
RX_GEAR=8, TX_GEAR=7,
RGB888,
Non-continuous D-PHY clock

1426

1715

1574

6

22

121.477

112.5

Dual Rx to Dual Tx,
RX_GEAR=16, TX_GEAR=14,
RGB888,
Non-continuous D-PHY clock

2609

3685

2964

12

22

95.247

64.285

«
...
26
27
28
29
30
...
»

Summary of Contents for MIPI
































Reviews:

No comments