background image

LTRx-512 Installer’s Guide 

Power Supply Schematics 

57 

Limited One-Year Limited Warranty 

 

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a 
period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The 
conditions of this warranty and the extent of the responsibility of Lathem Time Corporation (“Lathem”) under this 
warranty are listed below. 
 

1.

 

This warranty will become void when service performed by anyone other than an approved Lathem 
warranty service dealer results in damage to the product. 

2.

 

This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which 
has had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired 
other than in accordance with instructions furnished by Lathem. 

3.

 

This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any 
expendable parts that are readily replaced due to normal use. 

4.

 

The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or 
replacement thereof, at the sole discretion of Lathem. 

5.

 

If it becomes necessary to send the product or any defective part to Lathem or any authorized service 
dealer, the product must be shipped in its original carton or equivalent, fully insured with shipping charges 
prepaid. Lathem will not assume any responsibility for any loss or damage incurred in shipping. 

6.

 

WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express 
warranty set forth above, the products are sold with no expressed or implied warranties of any kind, and the 
implied warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed.   
No warranties are given with respect to products purchased other than from Lathem or an authorized 
Lathem reseller and any such products are purchased "as is, with all faults."  In no event will Lathem be 
liable for any direct, indirect, special, incidental or consequential damages arising out of or in connection 
with the delivery, use or inability to use, or performance of this product.  In the event any limited remedy 
given herein shall be deemed to have failed of its essential purpose, Lathem's maximum liability shall be to 
refund the purchase price upon return of the product. 

7.

 

Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty service on 
this product. 

8.

 

This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may also 
apply. 

9.

 

Should any difficulties arise with the performance of this product during warranty, or with any Lathem 
authorized service centers, contact Lathem Time at the address below. 

 

Lathem Time 

200 Selig Drive, SW, Atlanta, GA  30336 

404-691-0405 

www.lathem.com

 

Copyright © 2007 Lathem Time Corporation. All rights reserved. 

Summary of Contents for LTR-512































































Reviews: