background image

ATX Installation and User’s Guide

 

Page 11 

Power Requirements 

Cylindrical lithium battery (2 batteries) or Optional AC adapter 
Specifications of optional AC adapter (Lathem part #VIE1800). 

Output voltage   : 6V DC 

Rated current  : 200mA 

Ripple voltage  : max 500mVrms (200mA load) 

Plug type             : EIAJ-2RA 

Polarity              : Center plus(+) terminal 

 

Troubleshooting 

 

Q.

  What happens if batteries die before I replace them? 

A.

  The  ATX  will  stop  working.  When  the  batteries  are  replaced, 

press  and  release  the  RESET  button  on  the  ATX.  It  will 
automatically  reset  time  when  it  receives  the  WWVB  signal. 
(This may take 24 hours). The battery  life is approximately 5 
years. When the batteries become low the display will show a 
low battery indicator “ ”. 

 

Q.

  Do I need batteries if I use an AC adaptor? 

A.

  No, batteries are bypassed when an AC adapter is used. 

 
Q.

  What do I do if TRNS does not flash after I press TRNS button? 

A.

  Verify the ATX is not listening for the WWVB signal. The ATX will 

not transmit until the listening period ends. 

 

Q.

  How many Wall Clocks can an ATX correct? 

A.

  As long as all Wall Clocks are in the range of the ATX, there is 

virtually no limit of the number of clocks it can correct. 

Q.

  What do I do if the time does not correct on the ATX after WWVB 

Summary of Contents for ATX





















Reviews: