background image

ATX Installation and User’s Guide

 

Page 15 

One-Year Limited Warranty 

Lathem warrants the hardware products described in this guide against defects in material 
and workmanship for a period of one year from date of original purchase from Lathem or 
from an authorized Lathem reseller. The conditions of this warranty and the extent of the 
responsibility  of  Lathem  Time  Corporation  (“Lathem”)  under  this  warranty  are  listed 
below. 

1.

 

This  warranty will  become  void  when  service  performed  by  anyone  other than  an 

approved Lathem warranty service dealer results in damage to the product. 

2.

 

This warranty does not apply to any product which has been subject to abuse, neglect, 

or accident, or which has had the serial number altered or removed, or which has 

been  connected,  installed,  adjusted,  or  repaired  other  than  in  accordance  with 

instructions furnished by Lathem. 

3.

 

This  warranty  does  not  cover  dealer  labor  cost  for  removing  and  reinstalling  the 

machine for repair, or any expendable parts that are readily replaced due to normal 

use. 

4.

 

The sole responsibility of Lathem under this warranty shall be limited to repair of this 

product, or replacement thereof, at the sole discretion of Lathem. 

5.

 

If it becomes necessary to send the product or any defective part to Lathem or any 

authorized  service  dealer,  the  product  must  be  shipped  in  its  original  carton  or 

equivalent, fully insured with shipping charges prepaid. Lathem will not assume any 

responsibility for any loss or damage incurred in shipping. 

6.

 

WARRANTY  DISCLAIMER  AND  LIMITATION  OF  LIABILITY:  Except  only  the  limited 

express warranty set forth above, the products are sold with no expressed or implied 

warranties of any kind, and the implied warranties of merchantability and fitness for 

a particular purpose are hereby expressly disclaimed.      No warranties are given with 

respect  to  products  purchased  other  than  from  Lathem  or  an  authorized  Lathem 

reseller and any such products are purchased "as is, with all faults."    In no event will 

Lathem  be  liable  for  any  direct,  indirect,  special,  incidental  or  consequential 

damages arising out of or in connection with the delivery, use or inability to use, or 

performance of this product.    In the event any limited remedy given herein shall be 

deemed to have failed of its essential purpose, Lathem's maximum liability shall be to 

refund the purchase price upon return of the product. 

7.

 

Proof of date of purchase from Lathem or an authorized Lathem reseller is required 

for warranty service on this product. 

8.

 

This Warranty grants specific legal rights. Additional legal rights, which may vary by 

locale, may also apply. 

9.

 

Should any difficulties arise with the performance of this product during warranty, or 

with any Lathem authorized service centers, contact Lathem Time

 at the address 

below: 

Lathem Time 

200 Selig Drive, SW

 

Atlanta, GA    30336 

800-241-4990 

www.lathem.com

 

 

Document Number: USG0074C 

Summary of Contents for ATX





















Reviews: