MODELO 2554
Rev. Q 9/15
9
2554ES
MODEL 2554
Rev. Q 9/15
4
2554ES
4. Alinee la
Montura de la Base de Apoyo
con la
Base del Motor
,
teniendo en cuenta que la ranura del cable en la parte inferior
de la montura de la base de apoyo debe apuntar hacia la parte
posterior del Ventilador. Adose la
Montura de la Base de Apoyo
a la
Base del Motor
con
(4) Tornillos Mariposa.
Cerciórese
de alinear la
Llave
del
Conjunto de la Base de Soporte
con
la
Muesca Localizadora
de la
Base Del Motor
.
(Figura 1)
Suavemente tire del
Cable Eléctrico
para evitar que quede flojo
y colóquelo en el
Orificio de Colocación del Cable
.
(Figura 2)
ARMADO
1. Para un armado más sencillo, deposite el Ventilador hacia abajo
para que la parrilla frontal y el panel de control apunten hacia
arriba.
2. Arme las Mitades de la Base de Apoyo encastrando las
Puntas
de
la
Base de Apoyo A
con los Orificios para
Puntas en la Base de
Apoyo B
. Conecte el
Cable Eléctrico
a través del orificio grande
en el centro de la
Montura de la Base de Apoyo
.
(Figura 1)
3. Asegure
(2) #8 X 3/8" (9.52 mm) Tornillos
en los dos orificios
externos en la parte inferior de la
Base
.
(Figura 2)
HERRAMIENTAS NECESARIAS PARA EL
ARMADO
(no incluida)
- Destornillador de Cabeza Phillips # 2
Puntas de la Base
de Apoyo A
Puntas de la Base
de Apoyo B
Puntas
Llave
Cable Eléctrico
Figura 2
Orificio de
Colocación
del Cable
Montura de la
Base de Apoyo
Figura 1
OPERATION
This Fan may be operated by the manual controls located
on top of the unit (as shown in
Figure 3
) or by the Remote
Control (shown in
Figure 4)
.
1. Remove the Fan from the carton and assemble as
instructed.
2. Place the Fan on a firm and level surface.
CAUTION:
Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The
unit may leave a residue that could darken, stain or leave
permanent blemishes on the finish of certain furniture sur-
faces, including wood surfaces, and/or hardwood floors.
3. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they
may slip partially or completely out of the
receptacle with only the slight movement of
the attached cord. Receptacles in this con-
dition may overheat and pose a serious fire
hazard; if covered by a curtain or drape, the
fire hazard is even greater.
4. Turn the Fan on by pressing the
Power Button
( ). A
light will appear when the Fan is turned on. This light will
remain lit until the unit is turned off.
5.
SPEEDS:
Press the
Fan Speed Button
( ) to desired
speed setting. Each time the Fan Speed Button is
pressed, the speed will change from high (3), to medium
(2), to low (1).
6.
OSCILLATION:
Press the
Oscillation Button
( ) to start
and stop the oscillation function.
7.
TIMER:
The timer function allows the unit to be set to
operate for a length of time from 1/2 hour to 7 1/2 hours, in
increments of a 1/2 hour. Press the
Timer Button
( ) to set
the length of time desired. Each time the timer button is
pressed, the time is increased by 1/2 hour. After reaching
7 1/2 hours, pressing the timer button once more will reset
the Fan to continuous running. The lights on the front of
the unit will light up appropriately with the length of time
that the Fan is set for.
8.
IONIZER:
The ionizer function on this Fan will operate
within any speed mode. Press the
Ion Button
once to
turn this function on and a second time to turn it off. The
Fan must be
ON
for the ionizer to be functional. When
the ionizer is turned on it will assist in the purification of
the room air.
9. To turn the Fan OFF, press the
Power Button
( ).
10.After turning the Fan off, unplug the unit from the
electrical outlet.
Figure 3
Fan Speed
Button
Oscillation Button
Timer
Button
Ionizer Button
Power Button
