background image

COD. 83119L.01EN

09//2016

14

If during operation of the stove fuel burns so fast that there is almost never flame in the burner (even it can

appears  the “

Er03

” alarm), it  is  because  the  air  supplied  by  the  extractor  is  excessive  for  the  amount  of

pellets that are loading.

In this case, we can do two things:

-

Decreasing the amount of supplied air with

negative steps

of the

fan

(

check

6.1.7

).

-

Increasing the fuel load with

positive steps

in

pellet calibration

(

check

6.1.6

).

Before  changing  the  fan  and  pellet  calibration, it  is  necessary  to  make  sure  everything  is

correct:  installation,  maintenance  and  cleaning,  etc. For  this  we  can  check  the  chapter

8-

ALARMS, MENSSAGES AND PROBLEMS

”.

It is preferable to change first the fan calibration, so the pellet load also modify the output of the

stove.

5. INSTALLATION

The installation of LASIAN Air Stoves must be only carried out by qualified staff,
following  the  manufacturer's  instructions and  in  accordance  with  all  standards
and  regulations  that  are  applicable. Otherwise,  the  manufacturer  is  not  liable  for
any accident.

5.1 CHOICE OF LOCATION

It is forbidden to install the stove outside (exposed to the atmospheric agents) or in wet areas,
as  well  as  in  bedrooms,  locations  with  bath  or  shower  and  in  places  where  there  is  another
heating unit if they do not have the suitable dimensions and devoid of an adequate airflow.

When we choose the location of the stove, we will try that the route until the flue gas duct connection were as short
as possible, and flue gas can be discharged easily (check paragraph “

5.4- DUCT OR CHIMMEY

”).

Since in both, the stove and in the flue gas ducts it can be reached high temperatures, you have to follow certain
rules and safety recommendations to prevent possible fires and dangerous situations, so to make the installation
check paragraph “

5.3- DOMESTIC FIRE PREVENTION

”.

To ensure the air supply for the combustion in the stove, and keep a suitable ambient conditions, it has to keep in
mind everything  with  reference  to  ventilation  which  is  explained  in  paragraph “

5.5- AIR  INTAKE  AND

VENTILATION.

We must also have a suitable power point near the stove (check paragraph “

5.6- ELECTRIC CONNECTION

”), so

that  the  installation  has finished,  the  power  cord that  comes  with  the stove can  be  connected  and  disconnected
easily.

To make easier the  loading of the pellet  and the access to the control panel, as well  as the maintenance  or any
intervention  in  the  stove, it  will  be  necessary  to  leave  a  minimum  distances  above  and  around  it. A  reference  to
follow might be the ones described in paragraph “

5.3.1 MINIMUM SAFETY DISTANCES

”, although at least on the

right side of stove, it would be convenient to leave a minimum distance of 400 mm. in order to access to the rear
side of the stove.

Installation and use of the product should be in accordance with the manufacturer's
instructions, obeying European, national and local regulations where the product is
installed.

5.2 UNPACKING

Unpack  the  product  carefully  so  it  does  not  get  damaged  or  scratched.  Remove  from  the  tank  of  the  stove  the
accessory bag (it contains the legs of the stove, the power cord, the remote control, for the models which take it
and the instructions manual) and from the combustion chamber possible pieces of polystyrene or cardboard used
to block the removable parts, etc.

Also keep out of reach of children parts of the packaging (plastic bags, polystyrene, etc.) that could be potentially
dangerous and dispose according to the existing laws.

Summary of Contents for AUDAX 6 KW

















































Reviews: