5
Instruction Manual
Column Press with Electric Pump “EE12018”
6. MAINTENANCE.
The hydraulic circuit of the press is closed, so in normal conditions no oil leakage should be coming up.
In case of oil leakage, after the proper repairing work, you should fill up the tank with hydraulic oil by LARZEP (
Ref. AZ8901
); the pump is equipped with an oil level
indicator to control the need quantity of oil.
As far as a non-continuous use of the press is concerned (1 hour per day), oil replacement should be done once a year.
To empty the tank, you should remove the cover and take the oil out to another container. Please, bear in mind the existing rules for waste processing
when handling the used oil.
Keep greasy and lubricated the pin bearings, the piston and in general all the parts that might be in friction.
USE ONLY LARZEP HYDRAULIC OIL
Other grades of oils or types of hydraulic fluid (such as brake fluid) may affect the performance of the equipment or cause the deterioration of the seals.
DO NO ATTEMPT TO FILL THE PUMP WITH OIL WHILE IT IS CONNECTED TO A CYLINDER WHICH IS SUSTAINING A LOAD
BECAUSE IT MAY OVERPRESSURIZE THE RESERVOIR WHEN THE PISTON RETRACS AND CAUSE DAMAGE OR INJURY
Always use the original
LARZEP
parts to prolong the service life of your hydraulic equipment.
LARZEP S.A
. or your authorized dealer can supply you with original
parts for simple maintenance work
PROBLEMS
POSSIBLE FAILLURES
SOLUTION
1. The piston does not advance.
- Prime less pump.
1. Feed the pump keeping it started some minutes.
- Dirty accumulated in the filter.
2. Extract and clean it.
-No oil in the reservoir.
3. Check the level.
- Cylinder pressure retainer damaged.
4. Replace the retainer.
-Directional valve damaged.
5. Replace the valve.
- Cylinders body damaged.
6. Repair the body of the cylinder.
- Pneumatic problem.
7. Check the installation.
2. The cylinder does not reach pressures.
- Pressure relief valve unrated.
8. Rate the valve.
- Cylinder pressure retainer damaged.
See Solution. 4.
- Cylinders body damaged.
See Solution. 6.
3. The cylinder does not maintain pressure.
- Cylinder pressure retainer damaged.
See Solution. 4.
- Directional valve damaged.
See Solution. 5.
4. The cylinder does not retract.
- Damaged return spring.
9. Replace the spring.
- Directional valve damaged.
See Solution. 5.
The solutions marked in black must be carried out by specialized personnel, for it, go to an authorized distributor that sold you the equipment or to LARZEP, S.A., we
have original spare part kits as well as the necessary personnel, do not doubt in contacting to us, we are to yours disposition.
Always use original spare parts LARZEP, you will extend the life utility of the equipment, in opposite case the company will not become person in charge of the
possible failures, damages or losses that take place.
7. WARRANTY.
LARZEP, S.A.
guarantees its products against all design and manufacturing defects for the durations of two years from the date of purchase. This guarantee does not
include the ordinary wear of both metal and non-metal parts, abuse, using the equipment beyond its rated capacity and any wear or damage incurred as a result of using
a hydraulic fluid which is not recommended by
LARZEP, S.A.
Please note that if the equipment is disassembled or serviced by anyone other than an authorized service dealer or by
LARZEP, S.A
., this guarantee is rendered null
and void.
In the event of a warranty claim, return the equipment, to
LARZEP, S.A
. or the authorized dealer which sold you the hydraulic equipment,
LARZEP, S.A
. will repair
or replace the faulty equipment, whichever is deemed most appropriate.
LARZEP, S.A.
shall not be held liable for any consequential damages or losses, which may
occur as a result of faulty equipment
