LAQUA LAQUA-PC200 Series Instruction Manual Download Page 83

Page: 83 / 98

Error messages and trouble shooting

The response is slow

The indicated value does not change/No response

Cause

How to solve problem

The electrode is dirty.

Clean the electrode.

The electrode is cracked.

Replace the electrode.

The response of electrode is affected
by the sample solution.

It is important to select an electrode that is
appropriate for the sample. Consult your dealer. To
confirm an electrode that is appropriate for the
sample, check the electrode selection guide in our
catalogue, or refer to our website.

Cause

How to solve problem

The electrode is cracked.

Replace the electrode.

The electrode is not connected
correctly.

Connect the electrode correctly.

Keys are locked.

Turn OFF the power, remove the batteries, and then
turn ON the power again.

The instrument is in HOLD state.

Cancel the HOLD state.

Instrument defect

Consult your dealer.

Summary of Contents for LAQUA-PC200 Series



































































































Search results

Summary of Contents for LAQUA-PC200 Series

Reviews:

Related manuals for LAQUA-PC200 Series

Brands by name

Popular brands

LAQUA LAQUA-PC200 Series, Instruction Manual

Search results

Summary of Contents for LAQUA-PC200 Series

Reviews:

Related manuals for LAQUA-PC200 Series

Brands by name

Popular brands