manualshive.com logo in svg

Lantronix WiPort-485, User Manual, Page: 59 / 75

Share
Download
Lantronix WiPort-485 User Manual Download Page 59

Configuration via Serial Mode or Telnet Port 

WiPort™ User Guide 

 

59 

Enable Enhanced Password (Y) ? _ 

The Y (Yes) option allows an extended security password of 16-characters for 
protecting Telnet access. 

Disable Port 77F0 (Hex) 

Port 77F0 is a setting that allows a custom application to query or set the eleven 
WiPort configurable pins when they are functioning as general purpose I/O (GPIO). 
Disable this capability, if desired, for security purposes. 

Disable Port 77F0h ? _ 

The default setting, the 

N

 (No) option, enables GPIO control. The 

Y

 (Yes) option 

disables the GPIO control interface. 

Factory Defaults  

Select 

7 Factory Defaults

 from the Change Setup menu to reset the unit’s Channel 

1 configuration, Channel 2 configuration, E-mail settings, and Expert settings to the 
factory default settings. The server configuration settings for IP address, gateway IP 
address, and netmask remain unchanged. The configurable pins’ settings also 
remain unchanged. The specific settings that this option changes are listed below: 

Channel 1 Configuration 

Baudrate 

9600 

I/F Mode 

4C (1 stop bit, no parity, 8 bit, RS-232C, no flow 
control) 

Port No 

10001 

Connect Mode 

C0 (always accept incoming connection; no active 
connection startup) 

Hostlist Retry Counter 

3 

Hostlist Retry Timeout 

250 (msec) 

Send Character 

0x0D (CR) 

All other parameters 

0 

Channel 2 Configuration 

Baudrate 

9600 

I/F Mode 

4C (1 stop bit, no parity, 8 bit, RS-232C, no flow 
control) 

Port No 

10002 

Connect Mode 

C0 (always accept incoming connection; no active 
connection startup) 

Hostlist Retry Counter 

3 

Summary of Contents for WiPort-485












































































Reviews:

No comments