manualshive.com logo in svg

Lantronix WiPort-485, User Manual, Page: 17 / 75

Share
Download
Lantronix WiPort-485 User Manual Download Page 17

 Configuration Using DeviceInstaller 

WiPort™ User Guide 

 

17 

the EOR (end of record) and binary options, which can be 
used for applications such as terminal emulation to UNIX 
hosts. 

Remote Port 

This field is available for configuration only when Active 
Connection is not set to 

None

. 

Set the remote TCP port number for the unit to make outgoing 
connections. This parameter defines the port number on the 
target host to which a connection is attempted.    
To connect an ASCII terminal to a host using the unit for login 
purposes, use the remote port number 23 (Internet standard 
port number for Telnet services). 

Use Host List 

This field is available for configuration only when Active 
Connection is not set to 

None

.  

If this option is set to 

True

, the device server attempts a 

connection from the host list.  This process stops at the first 
valid connection. 
The host list is disabled for Manual or Modem Mode. The unit 
will not accept a data connection from an incoming remote 
device when the host list option is enabled. 
For information on configuring the host list, see 

Host List 

Configuration

 on page 

14.

 

Modem Emulation Mode 

In Modem (Emulation) Mode, the unit presents a modem 
interface to the attached serial device. It accepts AT-style 
modem commands, and handles the modem signals 
accordingly.  
For more information on Modem Emulation Mode, see 

Modem 

Mode

 on page 47. 

Selecting 

Without Echo

 tells the modem not send an answer 

to the commands received (or display typed data). 
Choose 

Full Verbose

 for the unit to echo modem commands 

and respond to a command with a message string. 

Character Response

 tells the WiPort unit to echo modem 

commands and respond to a command with a single character 
response. 

Telnet Mode 

This field is available for configuration only when Active 
Connection is not set to 

None

.  Select 

True

 to permit a Telnet 

connection to the WiPort unit. 

Remote Host 

This field is available for configuration only when Active 
Connection is not set to 

None

. 

Denotes the destination IP address used with an outgoing 
connection.   

Connection Response 

A single character is transmitted to the serial port when there 
is a change in connection state. Default setting is 

None

. 

Disconnection 

Disable Hard Disconnect 

The TCP connection closes even if the remote site does not 
acknowledge a disconnect request. 

Disconnect with 
modem_control_in 

The connection drops when modem_control_in transitions 
from a high state to a low state. 

Disconnect with EOT 

The connection is dropped when Ctrl-D or Hex 04 is detected. 
Both Telnet mode and Disconnect with EOT must be enabled 

Summary of Contents for WiPort-485












































































Reviews:

No comments