manualshive.com logo in svg

Lantronix WiPort-485, User Manual, Page: 10 / 75

Share
Download
Lantronix WiPort-485 User Manual Download Page 10

Introduction 

10  

WiPort™ 

User 

Guide 

‹

 

Security alarms and access control devices 

‹

 

Time clocks and terminals 

Protocol Support 

The WiPort device server uses the TCP/IP protocol stack for network 
communications. Other supported protocols include:  

‹

 

ARP, UDP, TCP, ICMP, Telnet, TFTP, AutoIP, DHCP, HTTP, and SNMP for 
network communications and management. 

‹

 

TCP, UDP, and Telnet for connections to the serial port.  

‹

 

TFTP for firmware and web page updates.  

‹

 

IP for addressing, routing, and data block handling over the network.  

‹

 

User Datagram Protocol (UDP) for typical datagram applications in which 
devices interact with other devices without maintaining a point-to-point 
connection. 

‹

 

SMTP for e-mail transmission. 

Configuration Methods 

For the unit to operate correctly on a network, it must have a unique IP address on 
the network.  There are three basic methods for logging into the device server and 
assigning IP addresses (as well as setting other configurable parameters): 

DeviceInstaller

: Configure the ports and other features on the WiPort using a 

Graphical User Interface (GUI) on a PC attached to a network. (See 

3:Configuration 

Using DeviceInstaller

.) 

Web-Manager

: Through a web interface, configure the WiPort and its settings using 

the WiPort’s Web-Manager. (See 

4: Configuration using Web-Manager

.) 

Serial & Telnet Ports

:  There are two approaches to accessing Serial Mode.  Make 

a Telnet connection to the network port (9999) or connect a terminal (or a PC running 
a terminal emulation program) to the unit’s serial port. (See 

5:Configuration via Serial 

Mode or Telnet Port

.)

 

Addresses and Port Numbers 

Hardware Address 

The hardware address is also referred to as the Ethernet address or the MAC 
address. The first three bytes of the Ethernet address are fixed and read 00-20-4A, 
identifying the unit as a Lantronix product. The fourth, fifth, and sixth bytes are unique 
numbers assigned to each unit. 

Example:

 00-20-4A-14-01-18 

Note: 

Make note of the MAC address.  It is needed to locate the WiPort 

using DeviceInstaller. 

IP Address 

Every device connected to an IP network must have a unique IP address. This 
address is used to reference the specific unit.  The WiPort is automatically assigned 
an IP address on DHCP-enabled networks as it is DHCP-enabled by default. 

Summary of Contents for WiPort-485












































































Reviews:

No comments