Lantronix SM16TAT2SA Install Manual Download Page 18 | Manualshive

Page: 18 / 30

Lantronix SM16TAT2SA Install Manual Download Page 18

Lantronix

SMxTAT2SA Install Guide

33716 Rev. L

https://www.lantronix.com/

18

Installing SFP Modules

You can install or remove a mini-GBIC SFP module from a SFP port without having to power off the switch.

Note

: with Port Mode set to Auto, these Copper SFPs can be used: TN-SFP-T-MG, TN-GLC-T-MG, and

TN-GLC-T.

Note

: see the related SFP device manual for important Safety warnings. See the Lantronix

for our full

line of SFP transceivers. See the

for additional information. The Fiber Optic Association, Inc.is an

international non-profit educational association chartered to promote professionalism in fiber optics through

education, certification and standards.

Step 1:

Insert the module into the SFP port.

Step 2:

Press firmly to ensure that the SFP module seats into the connector.

Figure 9: Installing an SFP Module into an SFP Port

Connecting Devices

Firmware v1.01.1209 adds the PoE Force mode feature.

Note

: only connect PDs which support power input in

the 48~56V range to prevent damage to PDs. When the port is changed to Force mode, the port's PoE LED lights

immediately. See the

Web User Guide

for details.

RJ45

:

SFP

:

Figure 10: RJ-45 and SFP Ports

«
...
16
17
18
19
20
...
»

Summary of Contents for SM16TAT2SA































Reviews:

No comments