manualshive.com logo in svg

Lantronix SM16TAT2SA, Install Manual, Page: 14 / 30

Share
Download
Lantronix SM16TAT2SA Install Manual Download Page 14

Lantronix 

 

SMxTAT2SA Install Guide 

33716 Rev. L   

https://www.lantronix.com/

   

14 

By pressing the 

Mode/Reset

 button for less than 2 seconds to change LED modes (Link/Act/Speed Mode or PoE 

Mode) you can check the port status by reading the LED behaviors per the table below. 

Table 3: Port Status LEDs 

When Link/Act/Speed Mode LED Lit

 

LED 

Color 

State 

Description 

RJ45 Ports 

Green 

On 

The port is enabled and established a link to connected device, and 

the connection speed is 1000Mbps. 

Green 

Blinking  The port is transmitting/receiving packets, and the connection speed is 

1000Mbps. 

Amber 

On 

The port is enabled and established a link to connected device, and 

the connection speed is 10/100Mbps. 

Amber 

Blinking  The port is transmitting/receiving packets, and the connection speed is 

10/100Mbps. 

-- 

Off 

The port has no active network cable connected, or it is not established 

a link to connected device. Otherwise, the port may have been 

disabled through the switch user interface. 

SFP Ports 

Green 

On 

The port is enabled and established a link to connected device, and 

the connection speed is 1000Mbps. 

Green 

Blinking  The port is transmitting/receiving packets, and the connection speed is 

1000Mbps. 

Amber 

On 

The port is enabled and established a link to connected device, and 

the connection speed is 100Mbps. 

Amber 

Blinking  The port is transmitting/receiving packets, and the connection speed is 

100Mbps. 

-- 

Off 

The port has no active network cable connected, or it is not established 

a link to connected device. Otherwise, the port may have been 

disabled through the switch user interface. 

RJ45

:  

   

SFP

:  

 

 

 

Summary of Contents for SM16TAT2SA































Reviews:

No comments