Lantronix Open-Q 2100 User Manual Download Page 36

Page: 36 / 45

Open-Q 2100 Development Kit

Open-Q™ 2100 Dev Kit User Guide

•

DSI

1 x 4 lane DSI

•

Backlight

Built-in backlight WLED driver on PM8916-1

Primary external backlight (BL0)



Backlight control signals



External Power

•

Additional GPIOs for general purposes available

•

Touch Panel

Supports one touch screen controller

Supports I2C via BLSP5

Power specifications
The display connector supports the following power domains:

Display Signal

Power Domain

PM8916-1 LDO4 (1.8V)

TBD

PM8916-1 LDO17 (2.85V)

TBD

Carrier 12V

TBD

Carrier 1.8V

TBD

The Lantronix Display (Open-Q 210x LCD part number: QC-DB-J00005 ) is an additional display accessory

that can be used with the display connector J2400 on the carrier board. Please use 51position flex cable from

JAE (JF08 series) to connect display board and carrier board. This board allows users to interface with the

development kit via the LCD that comes preinstalled on the display board. The following figure illustrates the

interfacing connectors on the display board.

Note:

The display board comes as an additional add-on to the Open-Q 2100 Development Kit. To purchase

this, please visit

http://shop.intrinsyc.com

or contact Lantronix at

[email protected]

for details.

J400, Display connection to the carrier board

Summary of Contents for Open-Q 2100














































Search results

Summary of Contents for Open-Q 2100

Reviews:

Related manuals for Open-Q 2100

Brands by name

Popular brands

Lantronix Open-Q 2100, User Manual

Search results

Summary of Contents for Open-Q 2100

Reviews:

Related manuals for Open-Q 2100

Brands by name

Popular brands