Lantronix EPS2-100 Installation Manual Download Page 102

Page: 102 / 114

Frequently-used Commands

M - 10

DEFINE PORT nn DTRWAIT {EN|DIS}

When Enabled, the Server will not assert DTR on the port
when it is idle (no user logins or connections).

DEFINE PORT nn

FLOW

option

CTS

Specifies CTS/RTS (hardware) flow control.

{EN|DIS}

Activates or deactivates the currently-configured flow-
control method.

NONE

Removes the current flow control settings.

XON

Specifies XON/XOFF (software) flow control.

DEFINE PORT nn NAME

newname

Enter a name of up to 16 alphanumeric characters for the
specified port.

DEFINE PORT nn

PARITY

option

parity

Enter

even

odd

mark

, or

space

. Specifying

mark

space

will change the character size to 7 bits.

NONE

Specifies that no parity will be used (the default).

DEFINE PORT nn SPEED baudnum

Sets the port’s baud rate. Acceptable

baudnum

values

range from 300 to 115200 baud (or 230000 baud for
1ooBASE-T Servers).

Table M-2:

Port Commands, cont.

Command

Option(s)

Description

Summary of Contents for EPS2-100



















































































































Search results

Summary of Contents for EPS2-100

Reviews:

Related manuals for EPS2-100

Brands by name

Popular brands

Lantronix EPS2-100, Installation Manual

Search results

Summary of Contents for EPS2-100

Reviews:

Related manuals for EPS2-100

Brands by name

Popular brands