Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 8 | Manualshive

Page: 8 / 20

Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 8

Assembly Instructions

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 1989 Lanier R/C

8

8

Attach brackets to both top and bottom of

stab. Locate the eight 2-56x12” rods, 2-56
golden clevises, nylon swing in keepers,
and clevis retainer clips. Screw the clevis
approximately half way on the threads of
the 12” rod and attach to the bracket on
the stab.

Mark the rod at the point on the fin brack-

et where it should be bent. Bend 90
degrees and cut off at 3/8”. Insert into the
bracket and attach the swing in keeper.

Install the other 3 wires on top in the

same manner. Be careful not to put pres-
sure on any of the surfaces, after all the
wires are installed we will adjust the ten-
sion.

Align the bend of the tail wheel bracket

even with the back of the fuselage and
mark the location of the hole. Drill a 3/32”
pilot hole for the screws.

Using two #6x3/4” sheet metal screws,

screw the tail wheel bracket in place with
the flying wire bracket underneath the
front screw.

«
...
6
7
8
9
10
...
»

Summary of Contents for STINGER 120 ARF





















Reviews:

No comments