Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 20 | Manualshive

Page: 20 / 20

Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 20

Assembly Instructions

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 1989 Lanier R/C

20

20

Canopy Mounting Hardware

1. Phillips head metric screws

3mm x 20mm

2

2. Flat washers

2

Fuel tank

16 oz.

Glow stopper and line supplied

1

Decal Sheet

1

Instruction Booklet

1

Tool need to complete the
Stinger.

1. Drill and assorted bits
2. Hobby Knife with #11 blade
3. Masking Tape
4. T-pins or straight pins
5. Felt tipped pen/pencil
6. Rubbing alcohol
7. Paper towels
8. Phillips screwdriver
9. Allen wrenches
10. Metric tap 6mm.
11. Pliers (needle nose)
12. Mixing sticks
13. 36” yard stick or tape measure
14. Scissors
15. Moto tool with sanding drum.

Adhesives

1. Thin CA (cyanoacrylate) glue
2. Medium CA. Glue
3. CA remover/debonder
4. 5-Minute Zap Z-Epoxy
5. 30-Minute Zap Z-Epoxy
6. Zap Z-42 Threadlock
7. Zap Canopy glue.

Equipment Required

1. Four channel radio or better
2. Servos- 46in.oz. or better 5
3. 1200mah battery pack or larger
4. Y-connectors

1

5. 12” extensions (Aileron) 2

6. Heavy duty control arms to fit your

servos.

7. Switch harness (your radio)
8. Motor (gas or glow)

If gas , battery pack, and switch
for ignition.

9. Prop and 3-1/2” Spinner for your

motor.

10. Fuel line (for gas or glow)
11. Pilot figure (optional)

Throttle Hardware

1. E-Z connector

1

2. 2mmx51cm pushrod

1

3. Nylon clevis

1

4. Lite-ply servo mount

1

5. 3/8” sq. x 3/4” spruce blocks 2

«
...
18
19
20

Summary of Contents for STINGER 120 ARF





















Reviews:

No comments