manualshive.com logo in svg

Lanier R/C STINGER 120 ARF, Assembly Instructions Manual, Page: 16 / 20

Share
Download
Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 16

Assembly Instructions

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 1989 Lanier R/C

16

16

The servo mount can be glued to the side

of the fuselage just in front of the F2 bulk-
head (the one with the wing dowel holes).
There will be room for the fuel tank below
it and the ignition system can sit on top of
the tank. Install the E-Z connector on the
servo arm.

Drill a hole in the firewall to line up with

the throttle arm on your engine. Install the
pushrod with the nylon clevis on the
engine and the other end in the E-Z con-
nector. This set up shows a Fox 2.4, if you
are using a different engine you will have
to adjust accordingly.

throttle servo forward of the rails. If you
need the weight forward it can be mounted
in front of the F2 former.

throttle servo mounted in front of F2

Install the control arms on the servo in

the centered position and lay the pushrods
across the arms. Mark the position on the
arm over the center of the hole and make a
90 degree bend in the wire. Cut the end off
at 3/8” and install in the servo arm.

Install the nylon swing in keepers to

attach the pushrods. Don’t forget to install
the servo arm retaining screw. 

servo mount assembled

Throttle
servo 
mounted

Summary of Contents for STINGER 120 ARF





















Reviews:

No comments