manualshive.com logo in svg

Lanier R/C STINGER 120 ARF, Assembly Instructions Manual, Page: 4 / 20

Share
Download
Lanier R/C STINGER 120 ARF Assembly Instructions Manual Download Page 4

Assembly Instructions

Lanier R/C, INC. P.O. Box 458 Oakwood, Ga. 30566 PH 770 532 6401

© copyright 1989 Lanier R/C

4

4

Wing Assembly

Start with one wing panel. Locate the

ailerons and trial fit them on the wing. You
will need to determine which aileron is the
left and which is the right by trial fitting. 
Make sure all the hinges are aligned and
the aileron is flush with the wing tip. Now
locate the other aileron and wing panel and
fit the aileron. When you are satisified with
the fit remove the ailerons and lay them
behind the wing in the correct position.
The Robart hinges work best if installed in
both wing and aileron at the same time.
Apply a drop of oil in the hinge.Use 30
minute epoxy to glue them in. A syringe
works great, if you don’t have one 
use a 1/8” dowel or piece of 3/32” wire to
get the epoxy into the holes. With glue in
the holes, push the hinges in wing up to
the pin. Apply glue in the holes on the
aileron and slide aileron into place. Work
the aileron up and down several times and
the Robart hinges will rotate into position.
Make sure you have a tight fit between the
wing trailing edge and aileron leading edge.
Set aside to dry and install the other
aileron.

Locate the dihedral brace. 

Trial fit the brace into the slot. 

Now slide the other wing panel on the dihe-
dral braces 

Remove the covering on the edges of the

plywood that form the front hold down
tongue.

remove covering

Clamp wing hold down tabs
together while epoxy sets.

Summary of Contents for STINGER 120 ARF





















Reviews:

No comments