background image

 

8

 

INSTALLATION 

 

DANGER 

THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED.  
FAILURE TO GROUND THE APPLIANCE COULD RESULT IN 
ELECTROCUTION AND DEATH. 

WARNING 

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL 
QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING.  IMPROPER 
INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE 
TO EQUIPMENT.  UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL 
APPLICABLE CODES. 

 

NOTICE 

The data plate is located behind the front access panel. The range 
voltage, wattage, serial number, wire size, and clearance specifications 
are on the data plate.  This information should be carefully read and 
understood before proceeding with the installation. 

 

NOTICE 

The installation of any components such as a vent hood, grease 
extractors, fire extinguisher systems, must conform to their applicable 
National, State and locally recognized installation standards. 

 

ELECTRICAL CONNECTION 

A junction box is located on the right hand side underneath the range.  
Connection can be made through a knock out located on the junction box. 

The electrical connection must be made in accordance with local codes or 
in the absence of local codes with 

National Electrical Code 

latest edition 

(in Canada use

: CSA STD. C22.1

). 

The range can now be connected to power.

 

 

CAUTION 

BE SURE THE POWER SUPPLY VOLTAGE MATCHES THE VOLTAGE 
SPECIFIED ON THE NAMEPLATE LOCATED ON THE FRONT OF THE 
RANGE. 

 

Summary of Contents for RTC36A-480VM





















Reviews: