![background image](http://html1.mh-extra.com/html/lang/rf21smg-usub/rf21smg-usub_operation-and-service-manual_3614332015.webp)
15
Range Top Assembly (See Range Top Assembly)
1.
Put a 1/8” bead of red silicone inside socket at each end of top front assembly (5).
2.
Slide front of pan slide on left side (4) into channel in top front assembly (5) & behind flange
at front. At the same time the slide engages behind front side flange, the side must go into the
side socket with the silicone. Secure with 10-32x3/8-truss head machine screw on the side &
1 EA. 8-32x1/2 pan head machine screw with an 8-32 hex nut. Use 222 loctite
on all screw
threads.
3.
Do the same as above with the right hand side (2) plus feed the 6 wires back between the slide
channel and the side then down through the 2 each 3/4” plastic bushings.
4.
Insert center slide (3) under control box, & into 2 clips on the bottom of the control box.
Secure to the gutter with 2 each 10-32x1/2-phillips head machine screw, with 10-32 hex nuts.
Use 222 loctite
on all screw threads.
5.
Install the top rear (1), the same as the front except there is no clips at the back for the center
pan slide. It is to be attached by 2 each, 10-32x3/8 truss head machine screw ,
6.
Set the assembly on top of the oven and attach 4 side clips and 16 each, 10-32x3/8-truss head
machine screw, use 222 loctite
on all screw threads. When setting the top onto the oven the
6 wires must be routed down through the top of the oven.
7.
With oven control panel in front of oven, connect motor wires, oven element wires and door
switch wires (refer to wiring diagram #61105-29). Install the thermostat capillary tube.
Attach the terminal block, attach the 6 range top feed wires to the circuit breaker in the oven
control section (refer to wiring diagram #61105-29) install oven control panel (6) with 6 8-32
machine screws, and install damper knob. Caution,
DO NOT
allow thermostat capillary tube
to be close to electrical connections.
8.
Install element terminal covers (9) over elements on griddle plate.
9.
Install griddle plate (7) on top of range top, & block up front of plate with 2 pieces of 2x6 (not
supplied).
10.
Insert 4 wires from each set of elements into proper wire tube. Be sure the glass sleeving is
still on the set of 4 wires. This sleeving will slide over the wire pipe.
11.
Insert the thermostat bulbs into the clip in bottom of the proper element pan and tighten the
bulb screw. Lower the griddle plate down while pulling down and pulling slack out of wires
and capillary tube, into the control box. (Leave a round loop in wire from wire tube to
elements).
12.
Attach plate to range with 2 each 3/8 x 1/2 x 5/16-18 shoulder screws at rear and 2 each 3/8 x
1/2 x 5/16-18 shoulder screws at front
13.
Wire range & control panel referring to the wiring diagram #61105-29 and install control
panel.
CAUTION:
When installing control panel be sure that capillary tubes are
behind the wiring as to keep them away from electrical
connections.
14.
Install pans and pan front (8).
15.
Install front grab bar (10).
ASSEMBLY INSTRUCTIONS CONT’D
Summary of Contents for RF21SMG-USUB
