![background image](http://html1.mh-extra.com/html/lang/rf21smg-usub/rf21smg-usub_operation-and-service-manual_3614332013.webp)
13
STEP 1 (See Oven Assembly)
1.
Attach right bottom (1) and left bottom (2), using 10-32x3/8 truss head screw with one drop
of 222 Loctite
on each screw.
2.
Install 3/4 -10 to 1/2 - 13 threaded adapters in the leg nuts to fit the 1/2 - 13 studs in the 6”
legs. Lay the bottom assembly on the deck.
3.
Install oven back (4) to bottom, be sure that insulation slides together properly, and use 10-
32x3/8 truss head machine screw with 222 Loctite
.
4.
Install left side with insulation (3) using 10-32x3/8 truss head screws with 222 Loctite
. Be
sure insulation slides over insulation on bottom.
5.
Position the loose piece of insulation (5) at rear of oven as shown in the oven assembly
illustration.
STEP 2. (See Oven Assembly)
CAUTION:
Leave oven interior screws loose until all screws have been
installed and use a drop of loctite
on all oven interior screws.
1.
Put a 1/16 to 1/8 in. bead of red silicone on outside of two flanges (top and bottom) on right
side of oven interior and motor assembly (B), four flanges (all around) on back of oven
interior (C), two flanges (top and bottom) on left side of oven interior (D).
2.
Attach interior bottom (A) to right interior side and motor assembly (B) with 10-32x3/8 truss
head screws.
3.
Install interior back (C) to (A) and (B) using 10-32 truss head machine screw.
4.
Install interior left side (D) to (A) and (C) using 10-32 truss head machine screw.
5.
Install interior top (E) to (B), (C), and (D) using 10-32 truss head machine screw.
6.
Put 1/8-in. bead of red silicone around outside of interior flange of oven front (F) (at base of
flange as shown on illustration A).
7.
Install oven interior over flange on oven front (F) and into the silicone & secure with 10-
32x3/8-truss head machine screw, be sure to install bottom trim (G) under screws at bottom.
8.
Tighten all oven interior screws & seal portal corners with silicone (see oven assembly
illustration)
9.
Install door switch unit (H) to front (F) use 3, 1/4” SAE flat washers, 10-24 hex nuts & a drop
of 222 loctite
.
10.
Install firewall (J) under control panel mounting flange, and over motor, and element end
threads and damper lever.
11.
Install vent rod plate (K) to top rear of (J). Use #10 sheet metal screws.
ASSEMBLY INSTRUCTIONS
Summary of Contents for RF21SMG-USUB
