background image

 

ETL File# 68964 

REV. A

 

IMPORTANT READ 

FIRST IMPORTANT 

CAUTION 

THE GRIDDLE IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER 
SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE 
MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR 
PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO 
THE PLACE OF INSTALLATION. 

 

CAUTION 

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH GRIDDLE WILL BE 
LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE 
GRIDDLE. 

 

CAUTION 

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN 
CUT. 

 

DANGER 

THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED.  
FAILURE TO GROUND THE APPLIANCE COULD RESULT IN 
ELECTROCUTION AND DEATH. 

WARNING 

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED 
TO WORK WITH ELECTRICITY.  IMPROPER INSTALLATION CAN CAUSE 
INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT.  UNIT MUST BE 
INSTALLED IN ACCORDANCE WITH ALL APPLICABLE CODES. 

 

NOTICE 

The data plate is on top of the control box. The griddle voltage, wattage, 
serial number, wire size, and clearance specifications are on the data plate.  
This information should be carefully read and understood before proceeding 
with the installation. 

 

NOTICE 

The installation of any components such as a vent hood, grease extractors, 
fire extinguisher systems, must conform to their applicable National, State 
and locally recognized installation standards.

 

 

CAUTION 

BE SURE THE POWER SUPPLY VOLTAGE MATCHES THE VOLTAGE 
SPECIFIED ON THE NAMEPLATE LOCATED ON THE TOP OF THE CONTROL 
BOX 

 

NOTICE 

During the first few hours of operation you may notice a small amount of 
smoke coming off the unit, and a faint odor from the smoke.  This is normal 
for a new griddle and will disappear after the first few hours of use.

 

 

CAUTION 

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM 
COMBUSTIBLE MATERIALS. 

 

CAUTION 

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY.  IF SPILLS 
OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR 
FALLS. 

 

NOTICE 

The times and temperatures in this chart are intended as a general guide and 
starting point. Your actual times and temperatures may vary from this chart.

 

 

WARNING 

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.  NEVER SPRAY OR 
HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC. 

 

CAUTION 

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS 
MEMBRANES AND CLOTHING.  PRECAUTIONS SHOULD BE TAKEN TO 
WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE 
CLOTHING.  CAREFULLY READ THE WARNING AND FOLLOW THE 
DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED. 

 

 

 

 

Summary of Contents for LGD




















Reviews: