background image

6

UNPACKING

Receiving the Griddle

Upon receipt, check for freight damage, both visible and concealed.  

 

Visible damage should be noted on the freight bill at the time of delivery 

and signed by the carrier’s agent. Concealed loss or damage means loss or 

damage, which does not become apparent until the merchandise has been 

unpacked.
If concealed loss or damage is discovered upon unpacking, make a written 

request for inspection by the carrier’s agent within 15 days of delivery. All 

packing material should be kept for inspection. Do not return damaged 

merchandise to Star Manufacturing International. File your claim with the 

carrier.

Location

Prior to un-crating, move the griddle as near its intended location as practical. The crating will help 

protect the unit from the physical damage normally associated with moving it through hallways and 

doorways.

Un-crating

The griddle will arrive completely assembled inside a wood frame covered by a cardboard box and 

strapped to a skid.
Remove the cardboard cover, cut the straps and remove the wood frame.

 

THE UNIT IS EXTREMELY HEAVY.  FOR SAFE HANDLING, 
INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY 
APPROPRIATE MATERIALS HANDLING EQUIPMENT (SUCH AS 
A FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE THE UNIT 
FROM THE SKID AND MOVE IT TO THE PLACE OF  
INSTALLATION.

 

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN 
WILL BE LOCATED MUST BE DESIGNED TO SUPPORT THE 
WEIGHT OF THE GRIDDLE.

 

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK 
WHEN CUT.

CAUTION

Summary of Contents for 136TDI





















Reviews: