Landoll Brillion 3631-25, Operator'S Manual

Page: 48 / 138

2-32 F-979-0219
ASSEMBLY
Center Tooth Control Installation
Left Side
1. Attach a Tooth Control Clamp w/cutout to the left
Front Tooth Tube by placing the Tooth Control Clamp
on top of the Tooth Tube and a 4-Hole Plate under
the Tooth Tube with two 5/8-11 x 5 Bolts and two
5/8-11 x 2 Bolts and Locknuts,
Do Not tighten at this
time. See Figures 2-31 and 2-32.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Clamp Lugs. Position the Tooth Control Tube
over the top of the Cylinder Rod Clevis and between
the Tooth Control Clamp Lugs and insert a 1 x 6-1/2
Pin. Place a 1” Flat Washer on each side of the Pin
against the Tooth Control Clamp. Secure with 5/16 x
2 Roll Pins.
3. Position a Tooth Control Bracket on top of the left
Rear Tooth Tubes while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1” Flat Washer on
each side of the Pin against the Tooth Control
Bracket and secure with 5/16 x 2 Roll Pins. Tooth
Control Brackets should be aligned with each other.
Attach Tooth Control Brackets on the Tooth Tube by
sliding a Clamp Plate into the Tooth Control Bracket
Slot and under the Tooth Tube. Secure with 5/8-11 x
5 Bolts and Locknuts.
4. Position a Tooth Control Bracket on top of the left
Middle Tooth Tubes while straddling the Tooth
Control Tube. Insert 1 x 6-1/2 Pins. Place a 1” Flat
Washer on each side of the Pin against the Tooth
Control Bracket and secure with 5/16 x 2 Roll Pins.
Tooth Control Brackets should be aligned with each
other. Attach Tooth Control Brackets on the Tooth
Tube by sliding a Clamp Plate into the Tooth Control
Bracket Slot and under the Tooth Tube. Secure with
5/8-11 x 5 Bolts and Locknuts.
Right Side
1. Attach a Tooth Control Bracket on the top of the right
Front Tooth Tube by sliding a Clamp Plate into the
Tooth Control Bracket Slot and under the Tooth Tube.
Secure with 5/8-11 x 5 Bolts and Locknuts,
Do Not
tighten at this time. See Figures 2-31 and 2-32.
2. Lay the Cylinder Rod Clevis between the Tooth
Control Bracket Lugs. Position the Tooth Control
Tube over the top of the Cylinder Rod Clevis and
between the Tooth Control Bracket Lugs and insert a
1 x 6-1/2 Pin. Place a 1” Flat Washer on each side of
the Pin against the Tooth Control Bracket. Secure
with 5/16 x 2 Roll Pins.
3. Position a Tooth Control Clamp w/cutout on top of the
right Rear Tooth Tube while straddling the Tooth
Control Tube. Insert 1 x 6-1/2 Pins. Place a 1” Flat
Washer on each side of the Pin against the Tooth
Control Clamp and secure with 5/16 x 2 Roll Pins.
Tooth Control Clamps should be aligned with each
other. Attach Tooth Control Clamp on the Tooth Tube
with two 5/8-11 x 5 Bolts and two 5/8-11 x 2 Bolts
and Locknuts.
4. Position a Tooth Control Bracket on top of the right
Middle Tooth Tube while straddling the Tooth Control
Tube. Insert 1 x 6-1/2 Pins. Place a 1” Flat Washer on
each side of the Pin against the Tooth Control
Bracket and secure with 5/16 x 2 Roll Pins. Attach
Tooth Control Bracket on Tooth Tube by sliding a
Clamp Plate into the Tooth Control Bracket Slot and
under the Tooth Tube. Secure with 5/8-11 x 5 Bolts
and Locknuts.
Ensure that both linkages don’t bind and the Tooth
Control Clamps and the Tooth Tubes are positioned
correctly.
See Figure 2-31 . Tighten the Bolts and Nuts at
this time.