4
OPERATION AND MAINTENANCE
DANGER
NEVER ALLOW ANYONE TO RIDE ON
THE 876 WING SERIES TILLOLL AT
ANY TIME. ALLOWING A PERSON TO
RIDE ON THE MACHINE CAN INFLICT
SERIOUS PERSONAL INJURY OR
DEATH TO THAT PERSON.
DANGER
DISC BLADES ARE EXTREMELY
SHARP. EXERCISE EXTREME CARE
WHEN WORKING ON OR NEAR DISC
BLADES. DO NOT ALLOW DISCS TO
ROLL OVER OR FALL ONTO ANY BOD-
ILY
PART.
DO
NOT
ALLOW
WRENCHES TO SLIP WHEN WORKING
NEAR DISC BLADES. NEVER PUSH
WRENCHES TOWARD DISC BLADES.
DO NOT CLIMB OVER MACHINE
ABOVE DISC BLADES. FAILURE TO
STAY CLEAR OF DISC BLADE EDGES
CAN CAUSE SERIOUS PERSONAL IN-
JURY OR DEATH.
WARNING
ALL HYDRAULICALLY ELEVATED
EQUIPMENT MUST HAVE CYLINDER
LOCKOUTS INSTALLED OR BE LOW-
ERED TO THE GROUND, WHEN SERV-
ICING OR WHEN EQUIPMENT IS IDLE.
FAILURE TO TAKE PREVENTIVE
MEASURES AGAINST ACCIDENTAL
LOWERING CAN RESULT IN SERIOUS
PERSONAL INJURY.
DANGER
ALWAYS LOCK THE TRACTOR DRAW-
BAR IN THE CENTER POSITION WHEN
TRANSPORTING THE UNIT. FAILURE
TO DO SO CAN RESULT IN SERIOUS
INJURY OR DEATH AND CAUSE DAM-
AGE TO THE EQUIPMENT.
DANGER
WHEN TRANSPORTING THE UNIT,
PLACE CYLINDER LOCKOUTS IN THE
TRANSPORT LOCK POSITION AFTER
FULLY EXTENDING THE CYLINDERS.
INSERT THE LOCKOUT PINS TO SE-
CURE THE CYLINDER LOCKOUTS.
FAILURE TO LOCKOUT THE CYLIN-
DERS CAN CAUSE THE UNIT TO SET-
TLE DURING TRANSPORT, WHICH
CAN RESULT IN SERIOUS INJURY OR
DEATH AND CAUSE DAMAGE TO THE
EQUIPMENT.
CAUTION
WHEN TRANSPORTING FARM IMPLE-
MENTS ON PUBLIC ROADS, IT IS THE
RESPONSIBILITY OF THE OPERATOR
TO ABIDE BY STATE AND LOCAL
LAWS CONCERNING WIDE LOADS,
SPEED, SAFETY EMBLEMS AND
SAFETY LIGHTING EQUIPMENT.
DRIVE AT SAFE SPEEDS. PARTICU-
LARLY WHEN ROUNDING CORNERS,
CROSSING ROUGH GROUND OR
DRIVING ON HILLSIDES, TO PREVENT
TIPPING THE TRACTOR.
4-1
Summary of Contents for 876 Series
