3-36
F-733-1120
ASSEMBLY INSTRUCTIONS
WARNING
14. Attach reel/gang bar assembly to reel arms using
gang bar mount plate, 3/4-10 x 6 hex head cap
screws and double hex lock nuts.
Refer to Figures
for reel gang bar placement locations.
15. Attach yellow reflector decals on outer arms
Decals are located in the manual tube.
Reflector decal locations also shown in
Figures 2-1
thru 2-6.
Figure 3-36: Yellow Reflector Decal Placement
Final Assembly
1.
Attach a tractor to the implement and charge the lift
system hydraulics as described is
2.
Connect the hydraulic hoses on the hydraulic leveler
to the tractor. Fully extend and retract the hydraulic
leveler several times to remove any air.
3.
The fold system must be purged of air and filled with
oil BEFORE attempting to fold the implement. Air in
the system will allow the wings to fall uncontrollably
and may result in implement damage. Follow
instructions for charging the hydraulic fold system as
described in
“Hydraulic Fold System” on page 4-5.
4.
Connect lights to the tractor and verify operation.
5.
Check tires for proper inflation
6.
Level the implement from side to side as described in
“Leveling (Side to Side)” on page 4-8.
7.
Inspect the final implement assembly, and verify that
all bolts have been tightened, cotter pins spread, and
that there are no leaking hydraulic connections.
8.
Rotate each disc gang to verify that each gang
rotates freely. Adjust any scrapers that may have
shifted during shipment or assembly.
9.
Lubricate the implement at all locations
“Lubrication Maintenance” on page 4-24.)
10. Touch up with paint any areas that may have been
scratched during moving, handling, or assembly.
11. Thoroughly read and understand the operating
section before using the implement.
Do not attempt to lift heavy parts (such as the
frame, disc gangs, lift, pull hitch, or reel/gang bar
assembly manually. Use a hoist or a forklift to
move these parts into position.
Summary of Contents for 6250 Disc
