Landoll 2211 Operator'S Manual Download Page 69

Page: 69 / 74

5-1

Chapter 5

Troubleshooting Guide

The Troubleshooting Guide, shown below, is included to
help you quickly locate problems that can happen using
your 2211 Disc Chisel Disc. Follow all safety precautions
stated in the previous sections when making any
adjustments to your machine.

PROBLEM

PROBABLE CAUSE

SOLUTION

UNIT NOT PULLING EVEN

Disc gangs uneven depth

Adjust depth/rephase disc gang

cylinders

(See “Hydraulic Disc

Gang Lift System” on page 4-6.)

UNEVEN DEPTH

Unit not level when under power in the
field

Level unit front to rear

(See “Leveling

(Front-to-Rear)” on page 4-7.)

Excessive disc gang depth or down
pressure

Reduce disc depth.

Tire pressure too low

Check inflation.

Unit not level front to rear

Adjust unit to be level.

UNIT SIDE DRAFTS OR MOVES SIDE
TO SIDE

Lift wheels not carrying enough weight

Adjust depth stop and raise implement.

Unit not level front to rear

Adjust unit to be level.

SHANKS PLUGGING WITH RESIDUE

Unit not level

Level machine

(See “Leveling

(Front-to-Rear)” on page 4-7.)

Discs not cutting residue

Adjust disc depth or raise shanks to allow

more gang depth.

SHANKS NOT PENETRATING

Unit not level

Level unit front to rear

(See “Leveling

(Front-to-Rear)” on page 4-7.)

Excessive disc depth

Reduce depth

Points worn

Install new points.

WHEEL BEARING FAILURE

Triple-lip seals not installed correctly

Install seals with the lips pointing outward

away from the hub.

HYDRAULIC - DISC GANG LIFT
CYLINDER NOT FULLY EXTENDING

Hoses not properly connected

Check hose routing

HYDRAULIC - ENTIRE UNIT SETTLING

Depth stop valve not working

Repair valve

Summary of Contents for 2211











































































Search results

Summary of Contents for 2211

Reviews:

Related manuals for 2211

Brands by name

Popular brands

Landoll 2211, Operator'S Manual

Search results

Summary of Contents for 2211

Reviews:

Related manuals for 2211

Brands by name

Popular brands