Landoll 2211 Operator'S Manual Download Page 51 | Manualshive

Page: 51 / 74

background image

OPERATION AND MAINTENANCE

4-3

Hydraulic Lift System

The Disc Chisel is equipped with a hydraulic lift system to
raise and lower the unit in the field.



WARNING

Figure 4-2: Hydraulic Leak Detection

Figure 4-3: Installed Transport Locks

1.

The hydraulic lift system contains cylinders plumbed
together. It is important that the cylinders be
connected in the proper series for the lift system to
operate correctly.

2.

The hydraulic system is not filled with oil and should
be purged of air before transporting and field
operations. Carefully hitch the Disc Chisel to the
tractor and connect the hydraulic lift hoses. Check to
make sure the tractor hydraulic reservoir is full of the
manufacturer’s recommended oil. Slowly raise the
machine. With all cylinders fully extended remove the
1-1/2 X 16 transport lockouts

(See Figure 4-3.)

Store

transport lockouts as shown in

Figure 4-4.

Lower

and raise the unit to verify that cylinders are working
simultaneously throughout the stroke. Do not loosen
any hoses or fittings. Recheck tractor reservoir to
make sure it is within operating limits.

Figure 4-4: Stored Transport Locks

Escaping hydraulic fluid can cause serious
personnel injury. Relieve system pressure before
repairing, adjusting, or disconnecting. Wear
proper hand and eye protection when searching
for leaks. Use cardboard instead of hands (See
Figure 4-2.) Keep all components (cylinders,
hoses, fittings, etc.) in good repair.

1-1/2 X 16
LOCKOUT

CYLINDER
STOP L-PIN

1/8 HAIRPIN

installed trans lock

stored trans lock

1-1/2 X 16 LOCKOUT

CYLINDER STOP
L-PIN

1/8 HAIRPIN

«
...
49
50
51
52
53
...
»

Summary of Contents for 2211











































































Reviews:

No comments

Related manuals for 2211

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: Rangevision Pages: 31

Brand: Taber Pages: 27

Brand: ParaBody Pages: 4

Brand: YSI Pages: 70

Brand: jcb Pages: 41

Brand: Quincy lab Pages: 4

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Uchida Yoko Pages: 40

bionic power knee

Brand: Össur Pages: 2

BALANCE KNEE OM8

Brand: Össur Pages: 36

Brand: Össur Pages: 37

REBOUND DIABETIC WALKER

Brand: Össur Pages: 63

Brand: Össur Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands