Landoll 2211 Operator'S Manual Download Page 57 | Manualshive

Page: 57 / 74

background image

OPERATION AND MAINTENANCE

4-9

Disc Blades

1.

The 2211 Disc Chisel is equipped with 24" disc
blades.

2.

The 24” diameter blades are a full concavity blade
with a thickness of 4 ga (.256”) and are standard for
the 2211 Disc Chisel.

3.

Sharpening – In some cases there is a desire to
sharpen disc blades for improved cutting. There are
several people who roll-sharpen disc blades. Most
disc blades used today are made of chrome-boron
steel. The chrome-boron steel has a higher hardness
than traditional carbon-steel blades for increased
wear. Higher hardness makes roll sharpening more
difficult often with mixed results, and is not covered
by warranty. Disc blade manufacturers will not cover
any alterations to blades other than the place of
manufacture. Results from roll-sharpening damage
may not be immediate, and may take more than a
season to be noticeable. If you choose to sharpen
disc blades, check with local dealers for reputable
experienced sharpeners that will stand behind their
work.



DANGER

Disc blades are extremely sharp. Exercise
extreme care when working on or near disc
blades. Do not allow disc s to roll over or fall onto
any body part. Do not allow wrenches to slip
when working near disc blades. Never push
wrenches toward disc blades. Do not climb over
machine above disc blades. Failure to stay clear
of disc blade edges can cause serious personal
injury or death.

«
...
55
56
57
58
59
...
»

Summary of Contents for 2211











































































Reviews:

No comments

Related manuals for 2211

Brand: Rangevision Pages: 31

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: Fisher Scientific Pages: 42

Brand: SAMCHULLY Pages: 48

Brand: HAGS Pages: 5

Brand: HAGER WERKEN Pages: 2

Brand: XanLite Pages: 4

Brand: Zero88 Pages: 26

Brand: HAMOKI Pages: 7

Brand: H&S Pages: 56

Brand: Bartscher Pages: 20

Brand: Bartscher Pages: 24

Brand: H&S Pages: 32

Brand: RainPoint Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands