Landoll 2211 Operator'S Manual Download Page 44

Page: 44 / 74

3-28

F-571-0511 Edition

ASSEMBLY INSTRUCTIONS

Final Assembly

Attach a tractor to the implement and charge the lift
system hydraulics as described is

“Hydraulic Lift

System” on page 4-3.

Install the 1-1/2 x 16 lockouts on both 3-1/2 x 16
cylinders on the frame.

Connect lights to the tractor and verify operation.

Check tires for proper inflation

Level the Disc Chisel from front to rear as described
in

“Leveling (Front-to-Rear)” on page 4-7.

Inspect the final implement assembly, and verify that
all bolts have been tightened, cotter pins spread, and
that there are no leaking hydraulic connections.



CAUTION

Rotate each disc gang to verify that each gang
rotates freely. Adjust any scrapers that may have
shifted during shipment or assembly.

Lubricate the Disc Chisel at all locations

(See

“Lubrication Maintenance” on page 4-17.)

Touch up with paint any areas that may have been
scratched during moving, handling, or assembly.

10. Thoroughly read and understand the operating

section before using the Disc Chisel.

Figure 3-25: 1,200 Foot-Pounds of Torque

Tighten all 1-3/4" nuts to 1,200 foot-pounds of
torque (See Figure 3-25.)

300

POUNDS

PULL

4 FOOT

2md410-010943

Summary of Contents for 2211











































































Search results

Summary of Contents for 2211

Reviews:

Related manuals for 2211

Brands by name

Popular brands

Landoll 2211, Operator'S Manual

Search results

Summary of Contents for 2211

Reviews:

Related manuals for 2211

Brands by name

Popular brands