3-1
WING COULTER CHISEL CENTER FRAME ASSEMBLY
WARNING
DO NOT ATTEMPT TO LIFT HEAVY
P A R T S ( S U C H A S T H E F R A M E ,
COULTER GANGS, WHEEL LIFT, AND
PULL HITCH) MANUALLY. USE A
HOIST OR A FORKLIFT TO MOVE
THESE PARTS INTO POSITION.
IMPORTANT
READ ALL SAFETY PRECAUTIONS AT THE
FRONT OF THE SECTION BEFORE ATTEMPT-
ING
ANY
OF
THE
FOLLOWING
PROCE-
DURES.
3-1.1
Place center frame assembly on stands
approximately 36” high. The assembly area
should be a large level area of sufficient size
to accommodate the Wing Coulter Chisel
when fully assembled.
3-2
HITCH INSTALLATION
3-2.1
Attach the hitch weldment to the front of
the frame using hitch pins, 1-8 hex lock nuts,
and 1/2 x 2-1/4 slotted spring pins
(See Fig-
ure 3-1)
.
3-2.2
Move the jack to the forward mounting
tube and rotate to parking position to support
the front of the hitch.
3-2.3
Insert a 3/4-10 x 7 hex head cap screw
into the hose holder tube on the right side of
the hitch from the bottom side so the threads
point upward. Hold in place with a 3/4 pre-
vailing torque flange nut with the flange
pointing upward as well. Do not tighten this
cap screw, so the hose holder bracket may
pivot freely in this joint.
3-2.4
Slide the hose holder bracket over the
screw and secure with another 3/4 prevailing
torque flange nut.
3-2.5
Install a 3/8-16 x 3-1/2 all-thread screw
in the front of the hose holder bracket and
secure with a 3/8-16 hex nut.
3-2.6
Slide the hose holder clamp over the
3/8” screw and loosely start the wing nut on
top of the clamp. Hydraulic hoses will be
routed through the clamp after assembly.
IMPORTANT
THE CLAMP HAS TWO SIDES, SO THAT EX-
TEND HOSES CAN BE LOCATED ON ONE
SIDE AND RETRACT HOSES CAN BE LO-
CATED ON THE OTHER SIDE FOR REFER-
ENCE.
IMPORTANT
THE LEVELER TOWER MUST BE INSTALLED
SO
THAT
THE
NARROW
END
OF
THE
TOWER IS DOWN AND THE REINFORCED
HOLES ARE TO THE REAR OF THE MA-
CHINE.
3-2.7
Connect narrow end of the leveler tower
to the top hole of the hitch weldment using
1-1/4-7 x 9-1/2 hex head cap screw, slotted
lock washer, and hex nut.
3-2.8
Attach the leveler tube to leveler mount
plates on the lift using hitch pin, 1-8 hex lock
nut, and 1/2 x 2-1/4 grooved alloy pin.
3-2.9
Insert 1-1/2 flange bearings in loose end
of the leveler tube.
3-2.10
Connect loose end of leveler tube to the
rear top hole of the leveler tower using hitch
pin, 1-8 hex lock nut, and 1/2 x 2-1/4
grooved alloy pin.
3-2.11
Attach the hitch rod radius assembly to
the top front hole of the leveler tower using
1-1/4-7 x 8 hex head cap screw, slotted lock
washer, and hex nut.
3-2.12
Connect the remaining end of the hitch
rod radius assembly to the hitch weldment
using 1-1/4-7 x 8 hex head cap screw, slot-
ted lock washer, and hex nut.
3-2.13
Assemble
hitch
ring
to
the
hitch
weldment using 1-8 x 7-1/2 hex head cap
screws, hitch bushings, flat washer, and hex
lock nuts through the top hole. Use same
hardware, safety chain assembly, and flat
washers in the lower hole.
3-3
Summary of Contents for 2130
