background image

ZF SERIES PRESSURE WASHER  

OPERATOR’S MANUAL

5

LANDA ZF   

•  

REV. 9/02

11. When the machine is working, do not  cover or place

in a closed space where ventilation is insufficient.

12. Machines with shut-off spray guns should not be op-

erated with the spray gun in the off position for ex-
tended periods of time as this may cause damage
to the pump.

13. Protect from freezing.

14. Be certain all quick coupler fittings are secured be-

fore using pressure washer.

15. Do not allow acids, caustic or abrasive fluids to pass

through the pump.

16. Inlet water must be from a cold fresh water supply.

17. Do not allow CHILDREN to operate the pressure

washer at any time.

18. The best insurance against an accident is precau-

tion and knowledge of the machine.

19. Landa will not be liable for any changes made to our

standard machines or any components not pur-
chased from Landa.

PRE-OPERATION CHECK

❏ 

Pump oil (SAE 30W non-detergent oil, General)

❏ 

Cold water supply ( 6 gpm, 5/8", 20 psi)

❏ 

Hose, wand, nozzle (nozzle size per serial plate)

❏ 

Water filter (intact, non restrictive)

SET-UP PROCEDURES

1. Put teflon tape on the inlet fitting (about 3 wraps).

Screw on 3/4" garden hose swivel provided in bag.
Attach a 5/8" garden hose to inlet connector. Mini-
mum flow should be 3 gpm.

2. Attach high pressure hose by screwing hose con-

nector to pressure washer outlet, hand tight.

3. Assemble the wand by pushing the two halves to-

gether and then fix by turning the connector to
tighten.

4. Connect wand to trigger gun by turning the connec-

tor. Attach high pressure hose to trigger gun and
tighten.

5. Remove red oil plug on top of pressure washer and

replace with dipstick supplied. Remove plug from red
oil cap anytime the pressure washer is running.

6. Check oil level on sight glass on left side of pressure

washer. Oil level should be visible half way up the
sight glass (30 wt.  non-detergent). If oil level is not
visible as described, add oil as needed.

OPERATING INSTRUCTIONS

1. With power switch in OFF position, plug power cord

into a grounded receptacle of proper voltage and
amperage reading. Then push GFCI reset button at
end of power cord if required.

2. Turn on water at faucet and pull trigger on spray gun

allowing water to flow until all air has discharged from
system. Check for water leaks; tighten as needed.

3. With trigger spray gun off, turn power switch to ON

position and check for leaks.

Step 1:

 Connect water suction hose to the INLET

connector. We recommend the use of a reinforced

suction hose with internal diameter not less than

13mm. (1/2 inch)

Step 4

: Connect one end of the high pressure

hose to the spray gun (A) and the other to the

outlet connection (B). Assemble lance by

pushing the two halves together and then fix

by turning the connector.

Step 5: 

Replace the red oil

travel plug (1) with the black and

yellow dipstick (2) in the bag.

Step 6:

 Check

that the oil
level in the

sight glass is

at the halfway

level.

Summary of Contents for ZF2-10021D

























Reviews: