HOME DEPOT SGP • 8.913-917.0 • Rev. 08/13
OPERA
T
OR’S MANU
AL
PRESSURE W
ASHER
10
WARNING: Some de ter gents
may be harm ful if in haled or in-
gest ed, caus ing severe nau sea,
fainting or poi son ing. The harm-
ful el e ments may cause prop er ty
dam age or severe injury.
STEP 1: Connect detergent in jec-
tor to discharge nip ple on ma chine,
Connect high pres sure hose to in jec tor with quick
coupler(check to make sure locking coupler sleeves
are in proper position be fore ap ply ing water pressure
STEP 2:
Use detergent de signed
spe cifi cal ly for pres sure washers.
House hold de ter gents could dam-
age the pump. Pre pare de ter gent
so lu tion as re quired by the man u-
fac tur er. Fill a con tain er with pres-
sure wash er de ter gent. Place the
fi l
ter end of de ter gent suc tion tube
into the de ter gent con tain er.
STEP 3:
Apply safety latch to spray gun trig ger. Turn
variable pressure control handle until discharge wa ter
exits both tubes.
NOTE:
De ter gent can not be ap plied
us ing Green or White noz zles.
STEP 4:
With the engine run ning, pull trig ger to op er ate
ma chine. Liq uid detergent is drawn into the ma chine and
mixed with water. Apply de ter gent
to work area. Do not al low de ter-
gent to dry on sur face.
IMPORTANT: You must flush
the detergent in jec tion sys tem
after each use by plac ing the
suction tube into a buck et of
clean wa ter, then run the pres-
sure wash er in low pres sure for 1-2 min utes.
THERMAL PUMP PROTECTION
If you run the engine on your pres sure wash er for 3-5
min utes with out pressing the trig ger on the spray gun,
cir cu lat ing water in the pump can reach high tem per a-
tures. When the water reaches this tem per a ture, the
pump pro tec tor engages and cools the pump by dis-
charg ing the warm water onto the ground. This ther mal
de vice pre vents internal dam age to the pump.
CLEANING TIPS
Pre-rinse clean ing surface with fresh water. Place de-
ter gent suc tion tube di rect ly into clean ing solution and
ap ply to sur face at low pressure (for best re sults, limit
your work area to sec tions approximately 6’ square
and always ap ply de ter gent from bottom to top). Allow
de ter gent to re main on sur face 1-3 min utes. Do not al-
low de ter gent to dry on sur face. If sur face appears to
be drying, sim ply wet down sur face with fresh water. If
need ed, use brush to re move stub born dirt. Rinse at
high pres sure from top to bottom in an even sweep ing
mo tion keep ing the spray nozzle ap prox i mate ly 1’ from
cleaning sur face. Use over lap ping strokes as you clean
and rinse any sur face. For best surface clean ing action
spray at a slight an gle.
Recommendations:
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
dis tance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use
ex treme caution as pressure washer may re move
the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
sur face you plan to clean. High pressure wash a
small area, then check the surface for damage. If
no dam age is found, continue to pressure wash ing.
CAUTION - Never use:
• Bleach, chlorine and other corrosive chem i cals
• Liquids containing solvents (i.e., paint thinners,
gas o line, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam-
age the surface being cleaned.
RINSING
It will take a few sec onds for the de ter gent to clear.
Apply safe ty latch to spray gun. Select and in stall the
de sired high pres sure noz zle.
NOTE:
You can also stop
de ter gent from fl ow ing by sim ply re mov ing de ter gent
si phon tube from bottle.
WARNING
DETERGENTS AND CLEANING TIPS
Control
Handle
Detergent
Injector
Discharge
Nipple
High Pressure
Hose
Quick
Coupler
