background image

ENG  •  9.801-511.0  •  Rev. 9/13a

5

  PRESSURE 

W

ASHER  

DEALE

R’S MANU

AL

  

IMPORTANT SAFETY INFORMATION

WARNING

USE PROTECTIVE  

EYE WEAR 

AND CLOTHING  

WHEN OPERATING 

THIS EQUIPMENT.

WARNING: High pressure spray 

can cause paint chips or other 
particles to become airborne 
and fly at high speeds. To avoid 
personal injury, eye, hand and 
foot safety devices must be 
worn.

  9.   Eye, hand, and foot protec-

tion must be worn when  
using this equipment.

WARNING

EAR PROTECTION 

MUST BE WORN

WARNING: This machine ex-

ceeds 85 db appropriate ear 
protection must be worn.

WARNING

RISK OF INJURY.  

HOT SURFACES  

CAN CAUSE BURNS

WARNING: Risk of injury. Hot 

surfaces can cause burns. Use 
only designated gripping areas 
of spray gun and wand. Do not 
place hands or feet on non-in-
sulated areas of the pressure 
washer.

 

 10.  To reduce risk of injury, close supervision is neces

-

sary when a machine is used near children. Do not 
allow children to operate pressure washer. 

This 

machine must be attended during operation.

 

TRIGGER GUN KICKS 

BACK - HOLD WITH  

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 

securely with both hands be-
fore starting. Failure to do this 
could result in injury from a 
whipping wand.

11.   Never make adjustments on 

machine while in operation.

12.  Be certain all quick coupler 

fittings are secured before 
using pressure washer.

RISK OF INJECTION 

OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure de-

veloped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when op-
erating. Do not direct discharge 
stream at people, or severe 
injury or death will result. 

 

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine 

from freezing.

13.  To  keep  machine  in  best 

 

 

operating conditions, it is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

machine from freezing  

 

could cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol

-

low storage instructions specified in this manual.

 

WARNING

RISK OF 

ASPHYXIATION. USE 

THIS PRODUCT ONLY 

IN A WELL 

VENTILATED AREA.

WARNING: Risk of asphyxiation. 

Use this product only in a well 
ventilated area. 

 14.  Avoid installing machines in 

small areas or near exhaust 
fans. Adequate oxygen is 
needed for combustion or 
dangerous carbon monoxide 
will result.

 15. Manufacturer will not be liable for any changes 

made to our standard machines or any compo-
nents not purchased from us.

 16.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY 

FROM FALLS WHEN 

USING LADDER.

WARNING: Be extremely careful 

when using a ladder, scaffold-
ing or any other relatively un-
stable location. The cleaning 
area should have adequate 
slopes and drainage to reduce 
the possibility of a fall due to 
slippery surfaces.

 

 17.  Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 18. Do not operate this machine when fatigued or 

under the influence of alcohol, prescription medi-
cations,  or drugs.

19.   Follow the maintenance instructions specified in 

the manual.

WARNING: Use vapor fuel only.

20.   The LP models are designed to run on vapor pro

-

pane fuel. Do not use liquid fuel. Have a qualified 
serviceman install and service your equipment.

 21.  Never expose a spark or flame where there may 

be unburned gas present.

Summary of Contents for ENG4-2000

































Reviews: