Land Pride SC2560 Operator'S Manual Download Page 33

Page: 33 / 44

1/15/21

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

Table of Contents

Section 5: Maintenance & Lubrication

Cutter Blade Assembly

Figure 5-2

Refer to Figure 5-2:

8. Insert blade bolt (#1) through blade (#2),

dishpan (#3) and flat washer (#4). Secure blade with

a new lock nut (#5).

9. Torque lock nut (#5) to 450 ft. lbs.
10.

Refer to Figure 5-1:

Replace blade bolt access

cover.

11. If replacing dishpan (#3) shown in Figure 5-2, nut on

gearbox output shaft should be torqued to 450 ft-lbs.

minimum and secured with a cotter pin with both

cotter pin legs bent opposite directions around the

nut.

24590

Land Pride Cutter Blade Parts

Item Part No.

Part Description

318-586A BLADE BOLT KIT (Contains #’s 1, 4, & 5)

802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY

820-112C SC2560 CUTTER BLADE 1/2 x 4 x 25 CW

820-249C SC2572 CUTTER BLADE 1/2 x 4 x 29 CW

316-124H WELDMENT DISHPAN SC2560

312-811H WELDMENT DISHPAN SC2572

804-147C WASHER FLAT 1 HARD ASTMF436

803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE

Use 1-11/16" Socket

Wrench On Blade Nut (#5)

IMPORTANT:

Examine blade bolts (#1) and

washers (#4) for excessive wear and replace if worn.

IMPORTANT:

Locknuts can loose their ability to lock

properly once removed. Always use a new locknut

when installing blades.

Skid Shoe Maintenance

WARNING

Excessive wear on skid shoes can damage side panels, cause

inadequate operation of cutter, and create a safety hazard.

Always replace skid shoes at the first sign of wearing thin.

Skid shoes should be inspected at the beginning of each

cutting season and replaced when material thickness is

less than 1/8" at any point. Order only genuine Land

Pride parts from your local Land Pride dealer.

Refer to Figure 5-3 on page 30:

Replace skid shoes as follows:
1. Raise the Rotary Cutter 3" or more off the ground and

place support blocks under the cutter. Make sure the

support blocks are positioned so they will not

interfere with skid shoe installation.

2. Lower cutter onto the support blocks, place Skid

Steer in park, set park brakes, shut the Skid Steer off

and remove switch key.

3. Remove 3/8" hex lock nuts (#3), lock washers (#4),

flat washers (#5), 3/8"

plow bolts (#2) and four skid

shoes (#1) from all four deck corners.

4. Plow bolts should be checked for wear and replaced

if necessary.

5. Install the new skid shoes (#1) to the four deck

corners with 3/8"

-16X1 1/4" GR5

plow bolts (#2), flat

washers (#5), lock washers (#4), and 3/8" hex lock

nuts (#3). Torque lock nuts (#3) to 31 ft-lbs.

6. Raise cutter up and remove support blocks.

Land Pride Standard Skid Shoe Bundle 326-827A

Item Part No.

Part Description

312-602D SKID SHOE, 1/4" x 2"

802-466C PLOW 3/8-16X1 1/4 GR5

803-013C NUT LOCK 3/8-16 PLT

804-013C WASHER LOCK SPRING 3/8 PLT

804-012C WASHER FLAT 3/8 SAE PLT

Land Pride Heavy Skid Shoe Bundle 326-828A

Item Part No.

Part Description

326-343D SKID SHOE HEAVY, 3/8" x 3"

802-466C PLOW 3/8-16X1 1/4 GR5

803-013C NUT LOCK 3/8-16 PLT

804-013C WASHER LOCK SPRING 3/8 PLT

804-012C WASHER FLAT 3/8 SAE PLT

Summary of Contents for SC2560













































Search results

Summary of Contents for SC2560

Reviews:

Related manuals for SC2560

Brands by name

Popular brands

Land Pride SC2560, Operator'S Manual

Search results

Summary of Contents for SC2560

Reviews:

Related manuals for SC2560

Brands by name

Popular brands