Land Pride SC2560 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 44

background image

Table of Contents

1/15/21

©

Copyright 2021 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 10

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . 10

Section 1: Assembly & Set-up . . . . . . . . . . . 11

Skid Steer Requirements   . . . . . . . . . . . . . . . . . . . 11
Dealer Preparations   . . . . . . . . . . . . . . . . . . . . . . . 11
Uncrating   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Float Chain Assembly  . . . . . . . . . . . . . . . . . . . . . . 12
SC2560 Motor And Hose Assembly   . . . . . . . . . . . 12
SC2572 Motor And Hose Assembly   . . . . . . . . . . . 13
SC2572 Vented Dipstick  . . . . . . . . . . . . . . . . . . . . 13
Hitch Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Hydraulic Hose Hook-up  . . . . . . . . . . . . . . . . . . . . 14
Gauge Wheel Assembly (Optional)  . . . . . . . . . . . . 15
Skid Shoe Assembly (Optional) . . . . . . . . . . . . . . . 16
Operator Protective Door (Optional)  . . . . . . . . . . . 17

Section 2: Adjustments . . . . . . . . . . . . . . . . . 18

Hitch Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Hitch Mounted Offset . . . . . . . . . . . . . . . . . . . . . 18
Hitch Mounted Centered . . . . . . . . . . . . . . . . . . 18

Height Adjustment Safety Chain  . . . . . . . . . . . . . . 19
Deck Leveling with
Optional Gauge Wheel  . . . . . . . . . . . . . . . . . . . . . 20
Deck Leveling without
Optional Gauge Wheel  . . . . . . . . . . . . . . . . . . . . . 21
Equipment Clearances  . . . . . . . . . . . . . . . . . . . . . 21

Section 3: Operating Procedures . . . . . . . . . 22

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 22
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 22
Transporting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cutting Instructions  . . . . . . . . . . . . . . . . . . . . . . . . 23
General Operating Instructions  . . . . . . . . . . . . . . . 24

Skid Steer Operating Instructions . . . . . . . . . . . 24
Rotary Cutter Operating Instructions . . . . . . . . . 25

Section 4: Optional Equipment . . . . . . . . . . . 26

Front Mounted Gauge Wheel   . . . . . . . . . . . . . . . . 26
Skid Shoe Bundles   . . . . . . . . . . . . . . . . . . . . . . . . 26
Motor and Hose Assemblies  . . . . . . . . . . . . . . . . . 26
Optional Case Drain Coupling  . . . . . . . . . . . . . . . . 27
Operator Protective Door   . . . . . . . . . . . . . . . . . . . 27

Section 5: Maintenance & Lubrication . . . . . 28

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 28
Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . . 29
Hydraulic Maintenance   . . . . . . . . . . . . . . . . . . . . . 30
Long Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 30
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 31

Hitch Plate Pivot . . . . . . . . . . . . . . . . . . . . . . . . . 31
Gauge Wheel Parallel Arms  . . . . . . . . . . . . . . . . 31
Gauge Wheel Spindle   . . . . . . . . . . . . . . . . . . . . 31
Axle Hub Bearing  . . . . . . . . . . . . . . . . . . . . . . . . 31
Motor Spindle Hub (SC2560 Only)  . . . . . . . . . . . 32
Gearbox (SC2572 Only) . . . . . . . . . . . . . . . . . . . 32

Section 6: Specifications & Capacities  . . . . . 33
Section 7: Features & Benefits   . . . . . . . . . . . 35
Section 8: Troubleshooting  . . . . . . . . . . . . . . 36
Section 9: Torque Values Chart . . . . . . . . . . . 37
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 39

«
1
2
3
4
5
...
»

Summary of Contents for SC2560













































Reviews:

No comments

Related manuals for SC2560

Brand: Zipper Mowers Pages: 28

Brand: Textron Pages: 16

Brand: Ducati Pages: 52

Brand: Kubota Pages: 28

Brand: Urrea Pages: 8

Brand: Esko Pages: 218

Brand: Larzep Pages: 5

Brand: Larzep Pages: 5

Brand: FONON Pages: 86

Brand: LOBSTER Pages: 13

Brand: Dolmar Pages: 110

Brand: ATIKA Pages: 110

Brand: Ruris Pages: 173

Brand: CanyCom Pages: 94

Brand: CanyCom Pages: 93

Brand: CanyCom Pages: 98

Brand: RASOR Pages: 15

Brand: Stihl Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands