background image

Table of Contents

1/7/19

© 

Copyright 2019 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future. 

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

RGR12 & RGA12 Series Rotary Tillers 311-948M

Table of Contents

Important Safety Information   . . . . . . . . . . . . .  1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol  . . . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction   . . . . . . . . . . . . . . . . . . . . . . . . . . .  7

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 7

Terminology  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Definitions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Further Assistance  . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 1: Assembly and Set-up . . . . . . . . . . .  8

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Dealer Preparations   . . . . . . . . . . . . . . . . . . . . . . . . 8
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . . 8
Park Stand Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cone Shield Adjustment  . . . . . . . . . . . . . . . . . . . . . 8
Upper Hitch Plate Assembly  . . . . . . . . . . . . . . . . . . 9
Manual Storage Tube Assembly  . . . . . . . . . . . . . . . 9
Lower 3-Point Hitch Pin Assembly   . . . . . . . . . . . . . 9
RGR12 Series Front Deflector   . . . . . . . . . . . . . . . 10
Rear Deflector Chain . . . . . . . . . . . . . . . . . . . . . . . 11

Chain Assembly Instructions   . . . . . . . . . . . . . . . 11

Driveline Assembly  . . . . . . . . . . . . . . . . . . . . . . . . 11
Hook-Up Rotary Tiller  . . . . . . . . . . . . . . . . . . . . . . 12

3-Point Hook-Up   . . . . . . . . . . . . . . . . . . . . . . . . 12

Driveline Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . 13
Check Driveline Collapsible Length . . . . . . . . . . . . 14
Check Driveline Maximum Length . . . . . . . . . . . . . 15
Check Driveline Interference  . . . . . . . . . . . . . . . . . 15

Section 2: Operating   . . . . . . . . . . . . . . . . . . .  16

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 16
Inspections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 16
Transport Rotary Tiller   . . . . . . . . . . . . . . . . . . . . . 17
Park Stand Operation  . . . . . . . . . . . . . . . . . . . . . . 18

Set Park Stand For Transport   . . . . . . . . . . . . . . 18
Set Park Stand For Storage  . . . . . . . . . . . . . . . . 18

Unhook Rotary Tiller  . . . . . . . . . . . . . . . . . . . . . . . 19
General Operating Notes   . . . . . . . . . . . . . . . . . . . 20
General Operating Instructions  . . . . . . . . . . . . . . . 20

Section 3: Adjustments   . . . . . . . . . . . . . . . . . 21

Rear Deflector Adjustment   . . . . . . . . . . . . . . . . . . 21
Skid Shoe Adjustment  . . . . . . . . . . . . . . . . . . . . . . 21
Park Stand Adjustment  . . . . . . . . . . . . . . . . . . . . . 22

Section 4: Maintenance and Lubrication   . . . 23

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tine Replacement  . . . . . . . . . . . . . . . . . . . . . . . . . 23
Driveline Protection  . . . . . . . . . . . . . . . . . . . . . . . . 24

Clutch Run-In  . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Clutch Disassembly   . . . . . . . . . . . . . . . . . . . . . . 24
Clutch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 25

Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 26
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 26
Lubrication Points   . . . . . . . . . . . . . . . . . . . . . . . . . 27

Driveline U-Joint  . . . . . . . . . . . . . . . . . . . . . . . . . 27
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 27
Driveline profile   . . . . . . . . . . . . . . . . . . . . . . . . . 27
Gear Case  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Bearing On Right End Of Rotor Shaft . . . . . . . . . 29

Section 5: Specifications & Capacities  . . . . . 30
Section 6: Features & Benefits   . . . . . . . . . . . 32
Section 7: Troubleshooting  . . . . . . . . . . . . . . 33
Section 8: Torque Values Chart  . . . . . . . . . . . 34
Section 9: Warranty   . . . . . . . . . . . . . . . . . . . . 35

Summary of Contents for RGR12 Series









































Reviews: