Land Pride RCM3615 Operator'S Manual Download | Manualshive

Page: 41 / 64

background image

Section 4: Options & Accessories

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

37

Table of Contents

Section 4: Options & Accessories

Safety Guards

DANGER

!

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Double row chain guards should

be used when cutting along roadways and in areas where

people may be present. Stop blade rotation if bystanders are in

or around the area.

WARNING

!

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Land Pride offers three types of safety guards to best suit
your application: rubber skirt guards, single row chain
guards, and double row chain guards.

•

Rubber skirt guards are designed for light duty
applications.

•

Single row chain guards are constructed with a single
row of hanging chain links. They can withstand harsher
applications than rubber skirts.

•

Double row chain guards are constructed with two
staggered rows of hanging chain links. The second row
provides an additional barrier for stopping thrown
objects.

Rubber Guards

330-482A

Front Rubber Guards

330-494A

Rear Rubber Guards

Single Chain Guards

330-481A

Front Single Row Chain Guards

330-493A

Rear Single Row Chain Guards

Double Chain Guards

330-483A

Front Dual Chain Guards

330-495A

Rear Dual Chain Guards

Tire & Axle Arrangements

Land Pride offers three different tires and three axle
arrangements to best suit your application:

•

Laminated tires: They are constructed of laminated
layers of solid rubber that will never go flat.

•

New foam filled tires: They are built tough to withstand
the rugged use a cutter receives, provides a smoother
ride when transporting and won’t go flat.

•

Used aircraft tires: They are built tough to withstand
the rugged use a cutter receives and to provide a
smoother ride when transporting.

•

4 - Wheel axle arrangement: Two tires on transport
axle and one on each wing axle.

•

6 - Wheel axle arrangement: Four tires on transport
axle and one on each wing axle.

•

8 - Wheel axle arrangement: Four tires on transport
axle and two on each wing axle.

Hitches

The cutter is factory supplied with the standard clevis
hitch. Other optional hitches are available. See

on page 13 for complete description of optional

hitches.

330-498A

Standard Clevis Hitch

330-333A

Bar-Tite Hitch (Optional)

330-335A

Ball Hitch (Optional)

330-501A

Pintle Hitch (Optional)

334-045A

LP Performance Hitch (Optional)

«
...
39
40
41
42
43
...
»

Summary of Contents for RCM3615

































































Reviews:

No comments

Related manuals for RCM3615

Brand: UnionSpecial Pages: 56

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

KOMPAN SPF28666S

Brand: Bommelland Pages: 23

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

Brand: ZOLL Pages: 37

Brand: Wacker Neuson Pages: 34

Brand: Wagan Pages: 4

Brand: Wachs Pages: 22

Brand: Abus Pages: 12

Brand: Tadano Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands