Land Pride APS15 Series Assembly Instructions Manual Download Page 8

Page: 8 / 10

Manual No. 313-473M

3/18/10

Land Pride

Assembly Instructions

Chain Guard Installation

Refer to Figure 12:
1.

Attach existing modified chain cover (#6) to the lower
drive chain assembly with hand knobs (#8). Tighten
knobs against the chain cover.

Slide guard support (#4) over end of right side
channel frame as shown.

Hook small seeds chain guard (#2) onto the two
guard mount stakes (#1) and secure in place with
rubber latches (#5).

Also secure chain guard (#2) to guard support (#4)
with hand knob (#7). Tighten knob against the guard
support.

Chain Guard Installation

Figure 12

26927

Illustration of Parts Shipped

Refer to Figure 13:
This illustration identifies shipping packages from the factory by part number.
See Land Pride’s Parts Manual 313-473P for part numbers of individual components.

APS1560 Small Seeds Box Shown

Illustration of Parts

Figure 13

52 Pitch Chain

70 Pitch Chain

90 Pitch Chain

26942

Summary of Contents for APS15 Series











Search results

Summary of Contents for APS15 Series

Reviews:

Related manuals for APS15 Series

Brands by name

Popular brands

Land Pride APS15 Series, Assembly Instructions Manual

Search results

Summary of Contents for APS15 Series

Reviews:

Related manuals for APS15 Series

Brands by name

Popular brands