Land Pride 7000 Series Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 38

background image

Preparation and Setup

Table of Contents

9/16/20

7000 Series 556-433M

15

First time Field Adjustments

Pre-Leveling of Machine

Note: Pre-leveling of machine should be done on a good

level surface (preferably concrete). Insure all tire

pressure is set to recommended pressure. Raise

machine and hold lever to insure that the air has

been purged from the lines.

1. Lower machine till blades are just off the ground,

adjust the hitch turnbuckle until the front and rear

blades are equal distance to the ground.

Scraper Adjustment

Refer to Figure 9

2. To adjust the disk scrapers loosen the u-bolts (1) that

hold the disk scrapper assembly (2) to the scraper

tube (3) and move the scraper until it is about

1



8

”

from the disc blade.

Figure 9

Scraper Adjustment

TP-69483

1

2

3

«
...
17
18
19
20
21
...
»

Summary of Contents for 7000 Series







































Reviews:

No comments

Related manuals for 7000 Series

Brand: Makerfire Pages: 10

Brand: MacDon Pages: 89

Brand: Yates Pages: 2

Brand: JAC Pages: 100

Brand: GE Pages: 698

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: Waters Pages: 4

Brand: Waterpik Pages: 2

Brand: Waves Pages: 8

Brand: Airway Pages: 2

Brand: Crazy Foil Pages: 8

Brand: Rainbow Colour Changers Pages: 22

Brand: Protech Machinery Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands