background image

6

 

Pouring hot water down the drain may cause the Drain 

 

Tube to collapse. Allow only luke warm or cold water to 

 

enter the Drain Tube.

 

Pouring coffee, tea, or other 

 

similar substances down the drain may cause the Drain 

 

Tube to become clogged.

ATTENTION

10.  Reattach Drip Tray/Cup Rest to unit.

Remote Pump Installation

1.  If necessary, install water booster (Lancer PN MC-163172) 

between water supply and the unit.

2.  Using tubing cutters, cut water line and install tee fitting, then 

route appropriate tubing from the remote pump location to 

the tee fitting at water line. 

3.  Connect line from tee fitting at water line to the remote pump 

deck inlet regulator.

4.  Complete the carbonated water line connection between the 

remote pump deck and carbonated water inlet on the unit.

5.  Install a shut-off valve in the water line feeding the deck. If a 

separate water line is run for plain water, ensure that it also 

has a shut-off valve.

A

A. Oetiker Pliers           C. Pump Inlet

B. Line to Unit 

         D. Pump Outlet

B

C

D

A

B

C

D

A. Tee Fitting

B. Line to Plain Water Inlet

C. Line to Water Source

D. Line to Remote Pump

A

B

C

A. Oetiker Pliers           C. Pump Inlet

B. Line to Tee Fitting     D. Pump Outlet

D

Installing Remote Syrup Pumps

1. 

Install BIB rack and remote pumps according to              

manufacturers’ instructions.

2.  Once pumps and BIB rack are installed, measure and cut 

tubing to length between the pump CO

2

 inlets, then connect 

tubing to all pumps.

A

B

C

A. Syrup Pump

B. CO

2

 Line

C. Fitting

D. Oetiker Pliers

D

3.  Using tubing cutters, cut any pump CO

2

 supply line and 

install tee fitting, then route appropriate tubing from the CO

2

 

supply to the tee fitting at syrup pumps. 

4.  Connect tubing from dispenser syrup inlet to the syrup pump 

outlet fitting. Repeat for each syrup line/pump. 

A

B

C

A. Syrup Pump Outlet

B. Syrup Pump

C. Fitting

 

Use proper connector for syrup manufacturer

ATTENTION

A. Syrup Pump Inlet

B. Fitting

C. BIB Connector

D. Oetiker Pliers

A

B

C

D

5.  Install BIB (bag in box) connectors onto the syrup pump inlet 

tubing.

6. 

Connect syrup BIBs to connectors. Repeat for each syrup 

line/pump.

Summary of Contents for FS 22

















Reviews: