background image

-7-

Assembly instructions: XL 8

8 m Telescopic Lance Series

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

8. Extend and twist to lock each section. Do not 

pull  sections  out  too  forcefully  as  joints  can  be 

over extended. 

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

Always extend and retract the pole

in a vertical position. Take care to twist

and unlock each section joint when

retracting.

Do not impact end of lance on the ground 

when retracting! Twist and push to release 

each section, ensuring the lance remains 
in the upright position.

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

9.  When  dusting    ensure  duster 

is  pressurised  to  3  bar  to  ensure        

efficient  product  application.  Dust 

blockages  can  occur  from  low     

pressures  usage.  Bar  pressures 

up  to  6  bar  can  be  used  for  liquid    

spraying.

Remove  the  cap  from  the 

safety pin, push through hole 

above  rubber  foot  and  refit 

yellow cap

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

Ensure the safety pin is in place 

when the lance is being used at 
lengths of less than 3m. 

10. Use lance to apply dust. Press 

trigger  for  short  burst  to  release 

product.

Montageanleitung Teleskop-Lanze XL 8 D 

Assembly instruction for telescopic lance XL 8 D 

Instruction de montage pour lance télescopique XL 8 D 

Istruzioni di montaggio per lancia telescopica XL 8 D 

 

 

Birchmeier Sprühtechnik AG 

 Im Stetterfeld 1 

 

      5608 Stetten

 

www.birchmeier.com 

max. 3 bar 

< 3 m 

5-10 sec 

(19.07.13) 

Summary of Contents for 8 m Telescopic Lance Series

















Reviews: