PAGE 3
TO INSTALL 5/8” POLY TUBE DRAIN LINE:
The poly tube insert is shipped attached to the drain line elbow’s locking clip.
Press the insert into the drain line (5/8” poly tube not included). Loosen nut of the drain line elbow. Press 5/8” poly tube with
insert into the drain line elbow until it seats on the back of the fitting. Tighten nut.
It is simplest to run the drain line into a sump pump pit or washing machine drain if possible. If this is not practical, a fitting
with a trap must be installed in a sewer line. Place the trap as close to the vent as possible to prevent siphoning of the trap
when large amounts of waste water go through the sewer line. DO NOT pipe the drain line solidly into the waste line, as this
is prohibited by most plumbing codes. The drain line should enter the trap from above so the water will not back up in the
drain line if sewer should become plugged up and the trap overflow. The trap should have a short pipe extending from it to
prevent splashing when water runs into the trap from drain line.
BRINE LINE CONNECTIONS:
3/8” poly tube is shipped within the instruction/warranty card packet affixed to the control
valve. One poly tube insert is shipped on the brine line elbow’s locking clip, the second is taped to the cap of the brine well.
Remove the locking clip by pulling straight out. Remove the white poly tube insert from the locking clip, and replace the
locking clip on the brine line elbow of the control valve.
Press the poly tube insert into the provided 3/8” poly tube. Press the poly tube and insert into the nut until it is fully seated
into the fitting. Do not use pipe dope or any other sealant on threads. Teflon tape is not needed on the threads. Tighten nut
securely to create a pressure tight connection. Pliers or crescent wrench may be used. The nut, gripper and retainer sleeve
is a three piece assembly that can come apart if removed from the elbow body. Parts must be reassembled exactly as
shown to function properly. If the nut is completely removed from the body, slip the nut, plastic gripper and retainer sleeve
on to the tube then tighten on to the fitting.
Click to buy NOW!
PD
F-
XC
H
A
NG
E
ww
w
.d
oc
u-
tr
ac
k.
co
m
Click to buy NOW!
PD
F-
XC
H
A
NG
E
ww
w
.d
oc
u-
tr
ac
k.
co
m
Install the second poly tube insert into the end of the 3/8” poly tube and repeat instructions above to install into the brine
tank’s brine line fitting.
BRINE TANK OVERFLOW PRECAUTION:
Attach a 1/2” poly tube (not provided) to the barbed fitting on the outside of the
tank. This poly tube should be piped to drain to allow brine to discharge to drain in the event of an overflow condition.
PROGRAMMING THE CONTROL VALVE:
Note: A quick-reference card is stored inside the front cover of the control valve.
To access this card, slightly pull tabs on side of cover outward and pull cover forward. Plug the electrical cord into a 115
Volt receptacle. DO NOT plug into an outlet controlled by a wall switch or pull chain that could inadvertently be turned off.
Wait a couple of seconds for control valve to “home” itself. Panel should display “TIME” and the time of day will be flashing.
SET TIME OF DAY
STEP 1: Press
SET CLOCK
.
STEP 2: Set current hour of the day by pressing ▲
or ▼ buttons. AM/ PM toggles after 12.
STEP 3: Press
NEXT
. Set current minutes by
pressing ▲ or ▼ buttons.
STEP 4: Press
NEXT
to exit
SET CLOCK
.
Click to buy NOW!
PD
F-XCHANGE
w
ww
.docu-track.c
om
Click to buy NOW!
PD
F-XCHANGE
w
ww
.docu-track.c
om
FIGURE 1
TO INSTALL 5/8” POLY TUBE DRAIN LINE:
The poly tube insert is shipped attached to the drain line elbow’s locking
clip. Press the insert into the drain line (5/8” poly tube not included). Loosen nut of the drain line elbow. Press 5/8” poly tube
with insert into the drain line elbow until it seats on the back of the fitting. Tighten nut.
It is simplest to run the drain line into a sump pump pit or washing machine drain if possible. If this is not practical, a fitting with
a trap must be installed in a sewer line. Place the trap as close to the vent as possible to prevent siphoning of the trap when
large amounts of waste water go through the sewer line. DO NOT pipe the drain line solidly into the waste line, as this is
prohibited by most plumbing codes. The drain line should enter the trap from above so the water will not back up in the drain
line if sewer should become plugged up and the trap overflow. The trap should have a short pipe extending from it to prevent
splashing when water runs into the trap from drain line.
BRINE LINE CONNECTIONS:
3/8” poly tube is shipped within the instruction/warranty card packet affixed to the control
valve. The poly tube inserts are shipped on the brine line elbow’s locking clip. Remove the locking clip by pulling straight out.
Remove the white poly tube insert from the locking clip, and replace the locking clip on the brine line elbow of the control valve.
Press the poly tube insert into the provided 3/8” poly tube. Press the poly tube and insert into the nut until it is fully seated into
the fitting. Do not use pipe dope or any other sealant on threads. Teflon tape is not needed on the threads. Tighten nut
securely to create a pressure tight connection. Pliers or crescent wrench may be used. The nut, gripper and retainer sleeve is
a three piece assembly that can come apart if removed from the elbow body. Parts must be reassembled exactly as shown to
function properly. If the nut is completely removed from the body, slip the nut, plastic gripper and retainer sleeve on to the tube
then tighten on to the fitting.
SET TIME OF DAY
STEP 1: Press
SET CLOCK
.
STEP 2: Set current hour of the day by pressing ▲
or ▼ buttons. AM/ PM toggles after 12.
STEP 3: Press
NEXT
. Set current minutes by
pressing ▲ or ▼ buttons.
STEP 4: Press
NEXT
to exit
SET CLOCK
.
SET
CLOCK
NEXT
▲
▼
REGEN
STEP 2
6:
35
PM
SET TIME
STEP 1
STEP 3
6
:35
PM
SET TIME
SET
CLOCK
NEXT
▲
▼
REGEN
SET
CLOCK
NEXT
▲
▼
REGEN
Install poly tube insert into the end of the 3/8” poly tube and repeat instructions above to install into the brine tank’s brine line
fitting.
BRINE TANK OVERFLOW PRECAUTION:
Attach a 1/2” poly tube (not provided) to the barbed fitting on the outside of
the tank. This poly tube should be piped to drain to allow brine to discharge to drain in the event of an overflow condition.
PROGRAMMING THE CONTROL VALVE:
Note: A uickreference card is stored inside the front cover of the control
valve. To access this card, slightly pull tabs on side of cover outward and pull cover forward. Plug the electrical cord into a 115
Volt receptacle. DO NOT plug into an outlet controlled by a wall switch or pull chain that could inadvertently be turned off. Wait
a couple of seconds for control valve to “home” itself. Panel should display
“TIME”
and the time of day will be flashing.
FIGURE 1
Page 3
3/8”
POLY TUBE
