Lanaform Breezy Cube User Manual Download

Page: 5 / 40

/ 40 English

Place the Breezy Cube personal air cooler
in the room half an hour before turning it
on to allow it to adjust to room temperature.

Filling the reservoir [

insert_photo

report_problem

Please note:

Before filling the device
with water, disconnect the
power adapter from the wall
socket and from the device.

Use only clean distilled or
demineralised water in order
to avoid any malfunction.

Make sure the reservoir
cap is tightly closed after
filling in order to avoid any
leakage or electric shocks.

The reservoir must be kept
clean. Please refer to the
chapter on “Maintenance

and storage” below.

• Remove the reservoir by lifting it

[

label

and keep it upside down

[

label

• Turn the reservoir cap in an anti-clock-

wise direction to open it

[

label

• Then pour clean, fresh, distilled or dem-

ineralised water into the reservoir

[

label

• Replace the cap and turn in a clockwise

direction to close it tightly.

• Before placing the reservoir on the base

of the device, make sure you close the
cooler tank drain plug tightly

[

insert_photo

label

11]

to avoid any leakage or electric shocks.

• Finally, fit the reservoir correctly on to

the base of the device.

Instructions for use [

insert_photo

report_problem

Do not move the air cooler

when it is being used or when
water is left in the reservoir.
In fact, a system for draining
water that has accumulated is
provided to ensure your safety
and this might cause leakages
when moving the device if
it still has water in it. Always
therefore empty the reservoir
before moving the device.

report_problem

Make sure your hands are

completely dry when connecting
and disconnecting the device.

The Breezy Cube personal air cooler comes

with a USB cable and an adaptor of 2.0A. Once
the air cooler is turned on, it is ready for use.

• Adjust the slots of the air vent upwards

or downwards to direct the air flow as
required.

• Press the ON/OFF button

[

label

: a blue

LED light indicates that the ventilation
and the atmospheric light are working.

• Press it a second time: the atmospheric

light is disabled.

info_outline

Turning the mood light off

enters the unit in night mode. It
then automatically switches to the
lowest intensity to be quieter. To
exit the night mode and return
to the previous settings, press
the intensity or timer button.

• The cooler runs continuously by default.

Press the timer button

[

label

once to set

the run time for 2 hours and a second
time to set a 4-hour run time. A blue
LED light indicates the length of time
selected.

• Press the intensity control button

[

label

to go from the lowest intensity to the
highest intensity and vice versa. A blue
LED light indicates the intensity selected.

• When the reservoir is empty, a red lu-

minous light appears on the ON/OFF
button

[

label

info_outline

The device can continue to be

used when the reservoir is empty
in order to benefit from the fan.
It is even recommended that the
fan be allowed to turn with the
reservoir empty from time to time
in order to dry the filter completely.

• If this same light flashes, the filter must

be replaced (approximately every 6
months). Please refer to the chapter on

“replacing the filter” below.

• Press the ON/OFF button once again:

the air cooler switches off.

report_problem

DO NOT LEAVE THE

DEVICE CONNECTED WHEN

YOU ARE NOT USING IT.

MAINTENANCE

AND STORAGE

• Always switch off the air cooler before

cleaning it or storing it.

• If the water contains too much calcium

and magnesium, it may deposit a “white
powder” in the device. If too much foam
is deposited on the device, this will pre-
vent it from working properly.

Maintenance

We recommend:

1 Using clean distilled or demineralised

water each time the device is used.

2 Cleaning the reservoir every 2 days.
3 Cleaning the device (see expla-

nations below) and making sure
that all of its parts are completely
dry when it is not in use.

To clean the reservoir:

1 Clean the water reservoir with

water using a soft cloth and
vinegar if there are any foam or
limescale deposits on the inside.

2 Rinse the reservoir in clean water.

To clean the filter:

1 Remove the filter by referring to

[

insert_photo

2 Clean by brushing with a soft

brush (not supplied).

To clean the surface of the cooler:

1 Clean the surface of the device

with a clean, soft, slightly damp
cloth as often as necessary.

2 Never use detergents, an excessive

volume of water, treated cloths,
cleaning agents or abrasive sprays.

Storage

If you do not intend to use the device for a
lengthy period, remove the filter and allow
it to dry completely

[

insert_photo

label

1-3]

, then wrap it

in a protective package and store it with
the clean, dry device in a cool, dry place
away from the light.

REPLACING THE FILTER [

insert_photo

For optimum performance, replace the filter
every three months or after approximately

500 hours of use. When the filter reaches the
end of its serviceable life, the light below

the “Refill/Filter” flashes

[

insert_photo

label

info_outline

If you live in a place where

the water is hard, it may need
to be changed more frequently.
In these cases, you will see
minerals accumulating on the
cooling device which might in
time obstruct the air flow.

• Disconnect the air cooler.

[

label

• Remove the air vent with the push-but-

ton at the top right of the vent.

[

label

• Take out the used filter.

[

label

• Then insert the new filter, making sure

it is positioned correctly as on the dia-
gram, i.e. with the opening towards the
bottom and slot it in towards you.