background image

INSTALLATION, OPERATING AND TROUBLESHOOTING INSTRUCTIONS FOR MODEL E12 

Page 15 of 20 

 

MANUFACTURER

S WARRANTY 

 

All  La  Marche  Manufacturing  Co.  equipment  has  been  thoroughly  tested  and  found  to  be  in  proper  operating 

condition upon shipment from the factory and is warranted to be free from any defect in workmanship and material 

that may develop within one year from date of purchase.  In addition to the standard one (1) year warranty, La 

Marche warrants it

s magnetics and power diodes on a parts replacement basis only for four (4) more years under 

normal use. 

 

Any part or parts of the equipment (except fuses, DC connectors and other wear-related items) that prove defective 

within a one (1) year period shall be replaced without charge providing such defect, in our opinion, is due to faulty 

material or workmanship and not caused by tampering, abuse, misapplication or improper installation.  Magnetics 

and power diodes are warranted for five (5) years after date of purchase.  During the last four (4) years of this five 

(5) year warranty period, the warranty covers parts replacement only, and no labor or other services are provided by 

La Marche, nor is La Marche obligated to reimburse the owner or any other person for work performed.  

 

Should a piece of equipment require major component replacement or repair during the first year of the warranty 

period, these can be handled in one of two ways: 

1.  The  equipment  can  be  returned  to  the  La  Marche  factory  to  have  the  inspections,  parts 

replacements and testing performed by factory personnel.  Should it be necessary to return a 

piece of equipment or parts to the factory, the customer or sales representative must obtain 

authorization from the factory.  If upon inspection at the factory, the defect was due to faulty 

material or workmanship, all repairs will be made at no cost to the customer during the first 

year.  Transportation charges or duties shall be borne by purchaser. 

 

2. If the purchaser elects not to return the equipment to the factory and wishes a factory service 

representative to make adjustments and/or repairs at the equipment location, La Marche's field 

service labor rates will apply.  A purchase order to cover the labor and transportation cost is 

required prior to the deployment of the service representative. 

 

In accepting delivery of the equipment, the purchaser assumes full responsibility for proper installation, installation 

adjustments  and  service  arrangements.    Should  minor  adjustments  be  required,  the  local  La  Marche  sales 

representative should be contacted to provide this service only. 

 

All sales are final.  Only standard LaMarche units will be considered for return.  A 25% restocking fee is charged 

when return is factory authorized.  Special units are not returnable. 

 

In  no  event shall La  Marche  Manufacturing  Co.  have  any liability  for  consequential damages,  or loss,  damage or 

expense directly or indirectly arising from the use of the products, or any inability to use them either separately or in 

combination with other equipment or materials, or from any other cause.  In addition, any alterations of equipment 

made by anyone other than La Marche Manufacturing Co. renders this warranty null and void. 

 

La Marche Manufacturing Co. reserves the right to make revisions in current production of equipment, and assumes 

no obligation to incorporate these revisions in earlier models. 

 

The failure of La Marche Manufacturing Co. to object to provisions contained in customers' purchase orders or other 

communications shall not be deemed a waiver of the terms or conditions hereof, nor acceptance of such provisions. 

 

The above warranty is exclusive, supersedes and is in lieu of all other warranties, expressed or implied, including any 

implied warranty of merchantability or fitness.  No person, agent or dealer is authorized to give any warranties on 

behalf of  the  Manufacturer,  nor  to  assume  for  the  Manufacturer  any  other  liability  in connection  with  any  of  its 

products unless made in writing and signed by an official of the manufacturer. 

 

Summary of Contents for CONSTAVOLT E12





















Reviews: