background image

INSTRUCTION / TROUBLESHOOTING MANUAL FOR MODEL A75MD

PAGE 22 OF 22

MANUFACTURER’S WARRANTY

All La Marche Manufacturing Co. equipment has been thoroughly tested and found to be in proper operating condition upon

shipment  from the  factory  and  is  warranted  to  be  free  from  any  defect  in  workmanship  and  material  that  may  develop

within  one  year  from  date  of  purchase.    In  addition  to  the  standard  one  (1)  year  warranty,  La  Marche  warrants  its

magnetics on a parts replacement basis only for four (4) more years under normal use.

Any part or parts of the equipment (except fuses, DC connectors and other wear-related items) that prove defective within

a one (1) year period shall be replaced without charge providing such defect, in our opinion, is due to faulty material or

workmanship and not caused by tampering, abuse, misapplication or improper installation.  Magnetics are warranted for five

(5) years after date of purchase.  During the last four (4) years of this five (5) year warranty period, the warranty covers

parts replacement only, and no labor or other services are provided by La Marche, nor is La Marche obligated to reimburse

the owner or any other person for work performed.

Should a piece of equipment require major component replacement or repair during the first year of the warranty period,

these can be handled in one of two ways:

1. The equipment can be returned to the La Marche factory to have the inspections, parts replacements

and testing performed by factory personnel.  Should it be necessary to return a piece of equipment or

parts to the factory, the customer or sales representative must obtain authorization from the factory.

If upon inspection at the factory, the defect was due to faulty material or workmanship, all repairs will

be made at no cost to the customer during the first year.  Transportation charges or duties shall be

borne by purchaser.

2.  If  the  purchaser  elects  not  to  return  the  equipment  to  the  factory  and  wishes  a  factory  service

representative to make adjustments and/or repairs at the equipment location, La Marche's field service

labor rates will apply.  A purchase order to cover the labor and transportation cost is required prior to

the deployment of the service representative.

In  accepting  delivery  of  the  equipment,  the  purchaser  assumes  full  responsibility  for  proper  installation,  installation

adjustments  and  service arrangements.  Should minor adjustments  be required, the local La Marche sales representative

should be contacted to provide this service only.

All  sales  are  final.    Only  standard  LaMarche  units  will  be  considered  for  return.    A  25%  restocking  fee  is  charged  when

return is factory authorized.  Special units are not returnable.

In no event shall La Marche Manufacturing Co. have any liability for consequential damages, or loss, damage or expense

directly or indirectly arising from the use of the products, or any inability to use them either separately or in combination

with other equipment or materials, or from any other cause.  In addition, any alterations of equipment made by anyone

other than La Marche Manufacturing Co. renders this warranty null and void.

La  Marche  Manufacturing  Co.  reserves  the  right  to  make  revisions  in  current  production  of  equipment,  and  assumes  no

obligation to incorporate these revisions in earlier models.

The  failure  of  La  Marche  Manufacturing  Co.  to  object  to  provisions  contained  in  customers'  purchase  orders  or  other

communications shall not be deemed a waiver of the terms or conditions hereof, nor acceptance of such provisions.

The  above  warranty  is  exclusive,  supersedes  and  is  in  lieu  of  all  other  warranties,  expressed  or  implied,  including  any

implied warranty of merchantability or fitness.  No person, agent or dealer is authorized to give any warranties on behalf of

the Manufacturer, nor to assume for the Manufacturer any other liability in connection with any of its products unless made

in writing and signed by an official of the manufacturer.

Summary of Contents for A75MD























Reviews: